It is located below the intake manifold. It is located below the intake manifold.
Persona - Kangta album - was created on 2005-06-13.
remove 13 mm nut connecting positive to starter motor, unclip smaller wire next to it, remove the three (3) bolts attaching starter motor to engine housing...that's how i just removed mine 5 minutes ago
I just removed a 1.7 Diesel starter motor. ALLWAYS DISCONNECT BATTERY NEGATIVE TERMINAL (10 mm) Remove top half of inlet manifold (8mm 12sided socket or spanner) Undo the two plastic bolts on the expansion tank (water bottle. 10mm) Move tank out the way Look down onto starter motor; remove bolt on which goes through bell housing into starter motor (16mm ) Jack car up; from underneath look up to starter motor, remove bolt which goes through the starter into gearbox (15mm) Remove nut from starter solenoid (little part of starter motor. 13 mm) Undo Philips bolt and disconnect wire You have removed your starter motor
Persona non grata - 2005 I is rated/received certificates of: Argentina:13 Australia:PG
The RPG Fanatic - 2010 Persona 4 Review 1-13 was released on: USA: 1 June 2010
Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.
Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.
Starter = Removal & Installation = 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.
Starter = Removal & Installation = 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.
Starter = Removal & Installation = 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.
Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.
Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. Start the engine several times to check starter motor operation.