Ford Ranger
Ford Ranger XL
Ford Ranger XLT

Where is the temperature sensor unit in a 4 cylinder 5 speed 1988 Ford Ranger with a 2.3 liter engine?

848586

Top Answer
User Avatar
Wiki User
Answered
2005-02-01 00:30:46
2005-02-01 00:30:46

I believe on that model there are two...one in the therm housing and one in the intake.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


The 1999 Ford Ranger 3.0 liter engine throttle positioning sensor is located on the cylinder head. The sensor will be near the middle of the cylinder head.

Where is the cylinder head temperature sensor on the 2003 ford explorer v8 engine

The Cylinder Head Temperature (CHT) sensor for the 2.3L engine is located between the two center ignition coils. The Engine Coolant Temperature (ECT) sensor for the 3.0L engine is located in the intake manifold to the right of the thermostat housing. The Engine Coolant Temperature (ECT) sensor for the 4.0L engine is located in the intake manifold behind the thermostat housing.

It is an electrical device that tells back the engine temperature to both the temperature gauge and (where fitted) the engine management system.

The variable reluctance sensor is the same as the crankshaft sensor on the 92 Ranger. It is on the front of the engine beside the crankshaft pulley.

Where is cylinder temp sensor on 2000 Ford f250 with v10 engine

According to Haynes Manual, 2001 and later 2.3L Ford Ranger, the Cylinder Head Temperature (CHT) sensor replaces the Engine Coolant Temperature (ECT) sensor on earlier models. The CHT sensor is located between the #2 and #3 spark plugs in the cylinder head and can be accessed through the valve cover. Carefully pull back the CHT cover to expose the electrical connector then disconnect it from the CHT sensor. Unscrew the CHT sensor and remove it. Installation is the reverse of removal, being careful not to overtighten the CHT sensor when installing it.

The camshaft position sensor is on top of the engine. It is on top of a shaft in the same place that older rangers had a distributor.

Bank 1 = The side of the engine the Number 1 cylinder is on Sensor 1 = between engine and catalitic converter Sensor 2 = After cat...

Code P1299: Cylinder Head Over Temperature Protection Active Indicates an engine overheat condition was detected by the cylinder head temperature (CHT) sensor. An FMEM Strategy called Fail-safe Cooling was activated to cool the engine. Engine cooling system concerns Low engine coolant level Base engine concerns

I BELIEVE the one for the engine temperature gauge is on the LEFT side of the thermostat housing ( where the top radiator hose connects to the engine ) and the sensor on the RIGHT is for the EEC - V ( when you are looking at the engine from the front )

The temperature sensor to the computer is located on the thermostat housing. On the 4 cylinder it is on the right side of the engine block.

The Engine coolant temperature sensor is installed in a coolant passage which is located at the front left cornerof the cylinder head.

engine coolant temperature sensor is faulty. engine coolant temperature sensor is faulty. engine coolant temperature sensor is faulty. engine coolant temperature sensor is faulty. engine coolant temperature sensor is faulty.

The 1999 F150 4.2 does not have a temperature sensor. It uses a cylinder head temperature sensor instead. It is mounted at the rear of the engine on the head.

motorcraft.com has a picture of the sensor and it is threaded , so it's threaded into the upper intake manifold somewhere ( at least that partially answers your question )

The engine coolant temperature sensor is usually on the front of the engine. The coolant temperature sensor will be in the vicinity of the thermostat housing.

To install a cylinder head temperature sensor on a F-250, you disconnect the cylinder head sensor from the electrical connector at the rear of the cylinder head. When installing the new one, you reverse the process of removal. The cylinder head temperature sensor is located by the O2 sensor.

On my 2000 International with a Detroit series 60 engine the water temperature sensor is on the back of the engine, passenger side in the cylinder head. Gears

I'm not a mechanic / technician but my Chilton repair manual does not show a knock sensor in the engine wiring schematic for the 2.3 liter 4 cylinder in a 1994 Ford Ranger

The Jeep Wrangler 2.5 liter engine intake air temperature sensor is located just above the exhaust manifold. The sensor will have to wires coming out of the top of it.

A coolant system temperature sensor controls it. : CHILTON calls it the cylinder head temperature sensor. Some after market manufacturers call it the coolant temperature sensor. These are equivalent.

1. Water temperature sensor Intake air temperature sensor cylinder head temperature sensor exhaus temperature sensor and catalytic sensor

The Engine coolant temperature sensor is installed in a coolant passage which is located at the front left cornerof the cylinder head.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.