Ford Ranger
Thermostats
Toyota Camry

Where is the thermostat located and how do you replace it located on a 1996 Ford Ranger 6 cylinder?

353637

Top Answer
User Avatar
Wiki User
2006-02-27 10:23:06
2006-02-27 10:23:06

follow the top radiator hose to the engine, remove it then remove the thermostat housing, remove the thermostat and replace it

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

locate the top radiator hose and follow it to the motor, unbolt the housing it is connected to and remove the old thermostat replace it and put it back together

User Avatar

find the top radiator hose, follow it to the motor take the housing off that the hose is connected too and the thermostat will be there remove the old one and replace with the new and replace the housing and hose

User Avatar

To change that thermostat you need to follow the top radiator hose to the motor from the radiator. It will lead to the thermostat housing on the block. The housing will be anchored with (2) bolts to the block (I think). Take the housing off and the thermostat is housed inside.you will have to replace it with a manufactured suggested thermo(probably 180* or 200 degree thermo).

User Avatar

If you need to replace the slave cylinder it is located in the bell housing and the trans has to be removed. The clutch master cylinder is located on the firewall on the drivers side

User Avatar

locate the top radiator hose and follow it to the motor, unbolt the housing it is connected to and remove the old thermostat replace it and put it back together

User Avatar

locate the top radiator hose and follow it to the motor, unbolt the housing it is connected to and remove the old thermostat replace it and put it back together

User Avatar

The thermostat on a 1984 ranger is located in the lower radiator hose housing connected to the engine, not the top like most vehicles..Fairly easy to replace. Just remove the bolts.. then the housing and the thermostat.

User Avatar

To replace the thermostat, follow the return hose from the radiator to the black plastic encasement which witholds the thermostat. It is pretty tricky to unbolt it from the engine (there are two bolts, one visible and the other is underneath the plastic piece) but that is where the thermostat is located. Good luck

User Avatar

where is the number 3 cylinder located on a 2.5 ford ranger engine

User Avatar

follow the top radiator hose to locate the thermostat housing, remove the hose from the housing then unbolt the housing. remove and replace the thermostat and rebolt the housing to the motor, replace the hose The housing is made of cheap metal and should be replaced. It is important to "seat" the thermostat properly. Also, it is much easier to replace and remove the thermostat housing if you first remove the timing belt housing.

User Avatar

Remove the 2 bolts at the thermostat housing. The upper hose goes to the thermostat housing.

User Avatar

follow the top radiator hose to the engine, the thermostat is located in the housing that that end of the hose is connected to

User Avatar

if it is a V6 you follow the bottom radiator hose to the thermostat housing and disconnect the electrical connector ( the housing is located at the front of the intake manifold) you loosen the hose clamp and remove the hose then take out the housing bolts and remove the housing and the thermostat is right there make sure you put the new one in the same way the old one came out

User Avatar

My 97 4.0 Ranger's thermostat is in the front of the engine. I has two bolts you have to take off. I had to replace the gasket. Leaked when I got on it hard. It's called the "thermostat housing. Thermostat is easy to replace. Great engine.

User Avatar

the thermostat is located on the outlet on top of the motor where the radiator hose is connected. remove the top radiator hose from the housing and there is two bolts holding the housing on the head of the motor, remove the bolts and you will find the thermostat. to replace just reverse the order in which it was taken off. hope this helps. john.

User Avatar

follow the top radiator hose to the motor the hose is clamped to the thermostat housing remove the housing and you will find your thermostat

User Avatar

Follow the upper radiator hose to the outlet/sensor housing then to the head. Remove the 2 bolts on holding the housing to access it.

User Avatar

The slave cylinder for your hydraulic clutch is located inside the transmission bell housing

User Avatar

follow the upper radiator hose back to the engine, and you will find the thermostat housing which is held onto the cylinder head by 2 bolts. The T-stat is located uder the t-stat housing.

User Avatar

its located on the back axle on the axle housing

User Avatar

where is the PVC valve located on a 1990 ford ranger 2.3 L

User Avatar

There is supposed to be an engine thermostat . Do you mean that someone has removed the engine thermostat ? What year of Ford Ranger and what year ?


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.