Follow the upper radiator hose to the engine and there is a housing there with the thermostat.Take the housing off and reokace the thermostat with the spring toward the engine. goodluckjoeAnswer
Just got done doing the same thing on my 1995 SE. Easy as pie, helped to remove the battery and followed hose as above. The thermostat is housed in a three way unit. Just unscrew the two nuts, and voila! Lost about a pint of fluid, mostly spilled out when I took out the thermostat, so if you have it in hand, you can pop it in rather quickly and replace rubber gasket with out having to buy a new one.
"reokace" is not a known word to me. Locate? Replace? Reposition? So far, this is meaningless.
how do you change a thermostat for a 1997 Ford Contour
this site^ will show you a how
locate the top radiator hose and follow it to the motor, unbolt the housing it is connected to and remove the old thermostat replace it and put it back together
Sounds As If You Need To Replace It. There Isn`t Much Of A Test To See If It Is Working Unless You Remove It. Replace It + Any Radiator, Heater Hoses, Bypass Hose Also.
stand at the front of the car and look for the top rad hose and follow it to the end there should be two bolts holding the hosing unbolt and replace the thermostat and gasket
It should be located on the top of the thermostat housing just at the right hand end of the engine. I am assuming that you are looking for the guage sensor.
Drain the water from your 1997 GMC Yukon cooling system. Remove the water supply hose. Remove the thermostat housing retaining bolts. Remove the old thermostat and replace with the new thermostat.
The thermostat is located underneath the radiator hose where it connects to the engine. The thermostat regulates the engine's temperature.
To replace the thermostat on a 1997 Pontiac Grand Am 3.1, first disconnect the negative battery terminal and loosen the clamp on the radiator hose. Next, remove the mounting bolts from the thermostat housing and insert the new thermostat.
The 1997 VW Jetta thermostat is located inside of the thermostat housing. Remove the thermostat housing retaining bolts. Remove the water supply hose. Reverse the process to install the new thermostat.
unscrew take old out, drop new in with gasket put baqck screws IF YOU DONT KNOW HOW TO CHANGE A THERMOSTAT, LEAVE YOUR HOOD CLOSED!
Most stats are located in the thermostat housing at the bottom of the upper radiator hose.
Replace the shocks and struts! :-D
Where do you find the Fuses
Remove the 2 bolts at the thermostat housing. The upper hose goes to the thermostat housing.
the thermostat is located on the front side of the intake manifold easy to get at
follow the top radiator hose to the engine and there will be two half inch bolts pull the housing off and that is your thermostat, replace in same position as the old one. p.s. is car overheating may not be thermostat, you can test thermostat in pan of boiling water and see if it opens or closes.
the thermostat is located behind the water pump. there are 2 8mm bolts holding it in. unscrew, pull old thermostat out, put new one in and put back together. Simple - 9 I would have given it a 10 but the bottom bolt can be a pin to get to.
The 1997 Nissan Ultima thermostat is located on the front of the engine. You can follow the water supply hose from the radiator to the thermostat housing.
The thermostat on a 1997 Mazda MPV is located on top of the engine, under the upper radiator hose. It controls the flow of coolant through the vehicle.
The thermostat on a 1997 Chrysler Town and Country is located under the housing where the upper radiator hose attaches to the engine.
The thermostat on a 1997 Ford F-250 is located under the upper hose assembly in the radiator. To locate the thermostat, drain the radiator halfway and remove the hose at the top of the radiator.
Its Located be hide the Exhaust manifold, You have to take off the Cat, to get to it
According to Haynes Repair Manual #61042 for the years 1993 thur 2001 fot the Mazda 626 & MX-6 Ford Probe the engine thermostat is located on the driver's side of the engine compartment under the air breather. It is necessary to disconnect the ram-air hose & remove the air-filter compartment to reach the thermostat. The thermostat is held in place by two bolts & an "O" ring gasket. I had to replace mine & is took a "little while" to remove everything to get to the thermostat, replace the thermostat & then replace everything back in place as it was before.