It is under the housing where the lower hose attaches to the block. The new thermostat should have the seal with it, and that should be all you need.
follow the top radiator hose to the engine, remove it then remove the thermostat housing, remove the thermostat and replace it
remove old thermostat and replace with new thermostat and gasket
Thermostat is located inside water outlet. You have remove the outlet if you want to replace the thermostat.
Remove the top radiator hose. The thermostat is located under the hose inlet on the engine. Remove the inlet to replace the thermostat.
thermostat is located on engine block. follow top water hose leading to engine. thermostat is located inside the water intake. remove hose. remove water intake(two bolts)housing. replace thermostat. .
The thermostat is located by the side of the cylinder block near the coolant inlet. Remove the coolant inlet housing after disconnecting cables and loosening the holding bolts. You will be able to remove the thermostat to replace it.,
generally the thermostat is located in the housing where the top radiator hose connects to engine.to change thermostat,you dump coolant,remove radiator hose from this housing.then remove housing,remove thermostat, install new one(making sure it is facing right way up).then replace housing, replace hose.fill with coolant
The thermostat is located in the housing and the engine end of the top radiator hose. Remove the 2 bolts and replace the thermostat.
can you show me governor for grand prix and how can i take it of. thermostat should be located on the left side of the motor inside thermostat housing housing needs to be remove to replace thermostat
The thermostat of a Vauxhall Zafira is located in front of the engine. The unit is on engine itself and has a main radiator hose connected to it. To replace it remove the hose and unbolt the house from the engine. Replace the thermostat in the housing.
The thermostat is located on top of the water pump. Remove the old thermostat by removing the hose and two (2) bolts. Clean the area around the "throat" to remove the old gasket. Reverse the process by installing a new thermostat.
The thermostat on a 94 Kia Sephia is located in the thermostat housing which is clamped to the radiator hose. To change it, remove the boltsÊon the thermostat housing, pull the thermostat out and replace a worn gasket. Ê
drain coolant then remove thermostat housing remove thermostat replace with new one spring to block
Remove the water supply hose from your 1988 Chevy Cavalier thermostat housing. Remove the thermostat housing bolts. Lift the old thermostat out and drop in the new thermostat.
located at the end of the upper radiator hose. remove two bolts, replace with new parts remember to replace the gasket.
Drain the water from the cooling system of your 1992 Saturn. Remove the water hose. Remove the thermostat housing retaining bolts. Take the thermostat out. Reverse the process to install the new thermostat.
To replace the thermostat on a 1998 Cadillac, locate the area you will be working in. The thermostat is located at the rear of the engine on the drivers side. Then locate the upper hose. Remove the upper hose from the housing and disconnect the unit. You can then safely replace the thermostat piece.
Follow the hose at the bottom of the radiator down to the alternator right below that are two bolts to remove to gain access to the thermostat. Remove the old one and install the new one.
Follow the top radiator hose back to the engine. This is where the thermostat is. Remove the 2 bolts and there it is.
Remove the thermostat housing. where is, and how do i remove the housing
To replace the thermostat on a 91 Cavalier you need to drain the radiator. Remove the top radiator hose and water inlet. Remove the thermostat from under the inlet. Install the new thermostat and reinstall the inlet and hose. Fill the radiator with fresh antifreeze.
Almost all thermostats are located at the motor where the top radiator hose connects to the motor. Drain the coolant, remove the 2 bolts in the thermostat housing, replace the thermostat, and replace the housing and refill the radiator.
You remove the old one and put a new one
I believe you want to drain the coolant, remove the top hose at the thermostat housing, remove the housing, replace the stat and gasket, reassemble fill with coolant and bleed the system.
First, remove the thermostat housing. Then grab the thermostat by hand and remove it.