Windshields and Wipers
Ford Explorer Sport Trac
Ford F-150

Where is the windshield wiper motor on a 1993 Ford F150?

373839

Top Answer
User Avatar
Wiki User
2006-04-01 23:16:20
2006-04-01 23:16:20

top of the fire wall under the hood your wiper arms will connect

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

To replace a windshield wiper motor for a 1998 F150, first remove the bottom trim on the window. Then remove both wiper blade assemblies and all screws on the metal cowling. Remove the retaining clip from the wiper motor linkage and pull the controls rods off.

User Avatar

The governor for the wipers is located near the fuse box. It is wired to the harness going to the wiper switch.

User Avatar

If the windshield wipers are not working in a 1998 Ford F150, the cause could be a blown fuse. There could also be a problem with the vacuum hoses connected to the wiper motor or the wiper motor itself.

User Avatar

First, remove the windshield wipers. Then you can remove the cowel just in front of the windshield. There are a bunch of screws connecting it to the firewall. Once you remove this, close the hood. Now everything is easily accessible and the rest is intuitive. Replace everything by using the opposite procedure.

User Avatar

Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.

User Avatar

Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.

User Avatar

Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.

User Avatar

Your windshield wipers were most likely overloaded and blew the fuse, try replacing the fuse. If that does not fix it then it is possible that the wiper motor burned out and will require replacement.

User Avatar

First you have to remove the wiper arms. Then remove the cowl plate between the windshield and the hood (screws will be in the top of the plate and inside the hood). This will give you access to the back of the wiper motor. There you will find a clip holding the wiper arm mechanism to the motor shaft. Remove the clip and the arm mechanism. Now remove the connectors and take the nuts off the front of the wiper motor. It will pull off the firewall. Reverse procedure to install new one.

User Avatar

The 1993 Ford F-150 has the most common hook-end wiper arms. See sources and related links below for installation videos. Locate and press the tab or button where the wiper blade is inserted into the hook of the wiper arm and pull wiper blade out of hook. You may have to rotate and flex the blade to make enough clearance for the hook to pass through.

User Avatar

If you'd like to replace a wiper motor on a Ford F-150 you need disconnect the negative battery cable, remove mounting bolts, and replace old wiper with new unit. When you've installed new unit connect electrical harness and wiper arm to motor.

User Avatar

Wiper blade sizes will vary depending on the year of the Ford F150. See sources and related links below to look it up.

User Avatar

I changed mine (1992) by removing the vented piece that runs between the windshield and the hood. Pop the hood and you will find screws to remove this as well as a a few screws from the top in between the grill type vents near the wiper blades. ( Remove the wiper arms and unscrew th antennae also) Lift this pc. out and you will gain access to the nuts that secure the motor to the firewall. Remove the motor harness, then disconnect the motor from the wiper connector. Try new motor by connecting to the harness and turning it on from the cab BEFORE you take anything apart. This will verify taht the motor is the problem. Good luck!

User Avatar

The 1993 Ford F1 50 windshield wipers to stop working. The fuse can be found in the fuse box. The location of the fuse is listed on the inside cover of the fuse box.

User Avatar

behind the passanger glove box on the right side. its a small black box.

User Avatar

Try popping off the cover at the bottom of the wiper. There should be a 15mm sized nut(I think). Make sure this nut is tightened down good. If that doesnt work then the linkage has come undone.

User Avatar

There is a C clip that holds them on.

User Avatar

Drivers side, bottom of windshield.

User Avatar

Can you put a 350 gm motor in 97 ford f150

User Avatar

attached to the jug. lower front.

User Avatar

how to replace an oil pan that goes to a ford f150 1993? how much does the pan cost,and can you show a picture of it?

User Avatar

There is no OBDII connector on 1993 F150. Didn't start until 1996 (97 model).


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.