0
Which part of a toilet tank assembly is the supply valve for water to the tank?
Wiki User
∙ 9y ago
That is a fill valve and is part of the ballcock system. When someone pulls the lever, that pulls the chain and lifts the flush valve flapper and empties the tank into the bowl. That causes the float to drop, opening the fill valve and allowing water from the supply to enter and refill the tank.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
How do you replace a flush valve in a toilet?
Have the new valve in hand. Cut the toilet water supply off at the commode, or even at the street meter box.Remove water tube or pipe supply and old flush valve. Install new valve and new supply line if required.
Where is the flush valve of a toilet?
The water supply line attaches to it on the bottom of the tank. The actual valve is at the top of this tube.
How do you replace float valve assembly?
not enough info to answer the question 1. Shut water off at wall. 2. Flush toilet to drain excess water from tank. 3. Remove supply line from bottom of tank.........
What is a toilet tank valve connected to?
It's connected to the incoming cold water supply pipe.
My toilet won't fill and the water supply is on?
Check the angle stop. Check the supply line. Then check the fluid master valve.
When I turned on valve to toilet after being off for a while no water is filling the tank?
Make sure your main water is turned on by turning on another sink or bath and if it is then turn your toilet valve off and on a couple times and see if any water comes out in your tank. If still no water is filling the tank then shut off the valve and take the supply tube off the valve and turn the valve on slowly to see if you have any water comming out. If still no water then your valve is plugged or your pipe to the valve is plugged which then you would need to clean out your valve or lines with the whole house water shut off. Sometimes I have seen that the plug is in between the valve an supply pipe connection and as soon i take the supply pipe off and turn on the valve it works just fine even when I put the supply pipe back to the toilet. I don't think it would be in your fill valve in your toilet tank unless you have pressure assist tanks and with them all you need to do is take out the screen inside them.
When you flush your toilet the water fills so slowly the flapper leaks what should you do?
remove and install a new filler valve and get a proper flapper for your toilet at a plumbing supply
Why is my Toilet tank not filling?
First check to see if the valve for the water supply is turned on. If that isn't the problem you may need to replace the tank water valve, they do wear out and are not that expensive or difficult to replace.
What part of a toilet tank is the supply valve for water?
The 'fill valve' is the one on the right side of toilet that has a pipe underneath running to a small valve on the floor or wall. These often go faulty. Not worth trying to fix it - new ones are cheap and easy to fit.
What is toilet water supply for pressure assisted?
Same as a regular toilet.
How do you stop a toilet tank condensation?
Install a tempering valve in water line feeding toilet. Tempering valve will mix hot and cold water together so warm water fills toilet tank which will stop condensation.
How do you stop a toilet from whistling when flushed?
It's something wrong with the pipes! One pipe is on too tight so it whistles when flushing. Here is THE answer!!! I did it to my own toilet. A plumber came over to fix our stuck toilet... The first thing he did was turn off the water supply valve at the back of the toilet. Then he unstuck our toilet. When he left, he turned the water supply valve back on, but he turned it up to high. the water pushes the air up through the pipe and the pressurized air comes out the top little slits on the stopper thingamagigie. To put in words you can understand, it's like blowing a flute. The Fast fix is to do this... Turn the water valve one way and then another. You will know when the water flows faster because the whistling will still be there. What you want to do is SLOWLY turn the water valve to the off position UNTIL the whistling stops and then a little more. You now have water coming in, but not at a speed to pressurize the air and make the whistling sound!
