0
The O-ring was invented by Niels Christensen (1865-1952); a Danish-American inventor.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
What is the past participle of invented?
Invented is the past participle of the verb invent. verb /past /past participle = invent /invented /invented
What were the names of the people who invented the internet?
Mr. Kamal Ahmad invented the internet Mr. Irfan Alam invented the invented
When was the rubber band invented and who invented it?
Was invented in 1916 by Femely H. Banbury
Who invented the heater?
who invented the heater
Who invented platforms?
Me I was the one who invented them.......
When was Nicole Oring born?
Nicole Oring was born on January 19, 1977, in Seoul, South Korea.
Groove depth for a 3.5 mm oring?
4.3 for static
What has the author Stuart A Oring written?
Stuart A. Oring has written: 'A comparative investigation of the similarities and differences in the aesthetic theories of Alfred Stieglitz, Edward Weston, Ansel Adams, and Minor White'
After installing a new fuel pump on a 1990 caprice how do you reattach that metal ring to the tank to finish the procedure?
that is a tricky metal ring (locking ring) there is a special tool for that.but if you are going to do this once no need to spend the money on a tool you will never use again. the trick is to get all the tabs started at the same time. there is an oring and you need to push the metal ring straight against the oring and turn clock wise until all the tabs catch. then get a chisel or screw driver and a hammer. there are outside tabs on the metal ring. tap them and turn the whole thing in clock wise.wala It is easier to fit the oring...if you will be sure the area is clean of any dirt and grit. Grease the area lightly on the tank, the area also where the oring contacts the tank, and the locking ring side to oring. Press firmly together, all tabs do need to be interlocked. Be sure oring is under and sealing. DO NOT STRIKE lock ring , to fit it in place. NO SPARKS.
Why paintball gun leak out barel when put on co2?
most likely a valve oring in damaged.
How do you change the distributor o ring on a 1997 Mitsubishi Galant?
remove the distributor and remove the oring. reverse removal procedure...oh be careful that you put the dist back in same way it came out or it wont start.this is done by marking rotor position. You also will need a timing light to reset timing. lubricate new oring
Chevy impala is making a muffling sound when driving?
Exhaust leak at Exhaust manifold to head gasket or oring at exhaust manifold pipe.
What is the icd-9-cm code for an infection of the skin on the lower leg unknown origin?
infection of the skin on the lower leg unknown oring
On a 93 lumina 31 liter can the oil pump drive be remove without removing the oil pump the drive leaks oil at the block seal and I'm trying to remove it to replace the seal?
the head has to be removed in order to get the drive out all of the way, but the easy way is to cut a notch at the top of the drive where it hits the head to get to the oring while it is still in the block then slide the oring over the top (after soaking in hot water is easier) once you get the new oring on get a SBC dist. gasket, splice it and put it around the top of the drive, the get some RTV silicone and goop it up to seal the gasket back together, this way takes about 2-3 hours and is WAY easier than removing the head,
What are some holidays in the united kingdom culture?
new years day st.patrticks day good friday esater monday boxing day oring may day crhistmass day
Is there an oring on the fuel intake bar on a3.1 olds engine?
Are you talking about the FUEL-RAIL ASSEMBLY that the fuel lines attach to? If so, YES. There are one on each line that goes into the rail assembly.
Why is new caliper leaking?
There are two reasons i know of . first the oring in the piston is either cut or twisted. The other is that the o ring on the piston is to small. The only cure is to replace it either way.
