answersLogoWhite

0


Best Answer

Your Idle Air Contol valve (IAC) may need to be cleaned. Refer to the following website for instructions http://www.geocities.com/adamk01452/IAC_Clean.html

User Avatar

Wiki User

โˆ™ 2008-11-22 17:11:01
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: Why 1993 Mazda 626 at low rpm stalls?
Write your answer...
Submit
Related questions

What is the Recommended tire pressure for low pressure tires Mazda 626-2.49 1992?

what is the tyres pressure for Mazda 626-2.48 1992(low pressure tyres)


Why would the handbrake light stay on in a 1993 Mazda 626 when not in use?

Either your handbrake switch is broken and will not turn off or you have low brake fluid.


Where is the low pressure port for the ac system for a 1998 Mazda 626?

The 1998 Mazda 626 low pressure port for your air conditioning system will be on the top of the air conditioner compressor. The low pressure port will be on the left-hand side of the compressor.


Where is the location of the service port for AC recharge on a 1990 Mazda 626?

The 1990 Mazda 626 air conditioning low pressure port can be found on top of the air conditioning compressor. The low pressure port should be labeled.


Where is the low pressure port for the AC system for a 2002 Mazda 626?

it should be in front of the radiator like on my 1998


What is diagnostic code p0117 Mazda 626?

Trouble code P0117 means:Engine coolant temperature circuit,low input


Where is low pressure port of ac 1990 Mazda 626?

WE finally found it on the compresson housing near the "S" suction , large hose connection.


Why does your 93 probe se redline at 4800 rpms?

Due to it's an 4 cyl. Mazda 626 2.0 Liters with a low gear change ratio.


Mazda RX7 1993 hrd to start and low idle RPM any ideas?

Power fc


Can you adjust the clutch pedal on a 1999 Mazda 626 It is engaging too close to the floor?

I believe you can but normally when it engages low its a sign that the clutch should be replaced soon.


Where is the airconditioning low pressure service port for a 2002 Mazda 626?

I have a 99 Mazda 626 and mine is on the passenger side of the car. Look for a black cylinder close to the firewall. You should find a small screwoff cap on the black cylinder. This is where you connect your hose to add freon. The high pressure and low pressure service ports are different sizes, so you can't get them mixed up and connect to the wrong one. Hope this helps!


Add freon to 2000 Mazda 626 air conditioner?

Its best to use a set of a/c gauges but if you are not then just add the freon to the low side which will be the larger hose (suction side)...


How do you Add freon to 2000 Mazda 626 air conditioner?

Its best to use a set of a/c gauges but if you are not then just add the freon to the low side which will be the larger hose (suction side)...


Why would the transmission on a 1993 Mazda Protege slip especially when going up hills and when it's cooler?

Possibly low of fluid. If it is not low, then have the transmission and filter changed and see if this helps.


Where is the low pressure ac port on a 1999 Mazda 626?

It is located on the passenger side near the fire wall on the big canister looking thing. Mine has a black cap on it. Just follow the line to the firewall and you will find it.


1999 Mazda 626 And sometimes it stalls after you come to a complete stop but if you turn it off and start it it turns back on no problem Why would it do that?

Answer The chances are that your "tick over" or rate at which your car naturally revs when in ignition, is too low for it to sustain internal combustion, causing your car to stall. Otherwise, it may be worth consulting your local mechanic to discuss problems with your ECU or engine management system, as it maybe that this is starving your engine of fuel.


What would cause the transmission to go in and out of overdrive on a 2000 Mazda 626?

it may be low transmition fluid pressure or you may have a solenoid messing up. have your vehicle scan for trouble codes. your vehicle's "T.C.M" should have an error code for that.


What would cause a 91 Mazda 929 that dies at low speeds when turning?

I have a Mazda 929 (1993) I had the same problem last year...I got a new alternator, and some new wires and spark plugs. Haven't had a problem with it since.


Why your car stalls when you turn the AC on?

The idle is set too low or there is an electrical problem


Why does Engine stalls when in low gear?

check for vacuum leak or dirty fuel filter


Use the word noisome in a sentence?

The noisome stalls at the fair were closed because of the low quality.


97 sebring loses power and stalls at low speed?

There could be a few reasons why a 1997 Chrysler Sebring loses power and stalls at a low speed. The thermostat could be bad, the battery cables could be lose, or a spark plug may need changed.


What might cause a 1993 Mazda mpv to overheat?

Low coolant Bad radiator cap Dirty or plugged radiator Thermostat cooling fan not working Water pump Collapsing hoses


Why is the brake warning light on in your 1993 Mazda cronos?

Parking brake not fully released? Worn brake linings? Brake fluid in reservoir low (mabe a leak in system)? Bad sensor?


How to change dashboard bulb for Mazda 626 1999 model?

two screws into cowl roof, remove them then drop steering as low as you can then take a firm grip of cowl bae and pull. then open screws that you see , tale out dash cluster and bulbs are on back, replace then refit .