The depth of field is so small that a very small vertical travel could shift the focus from the top of the specimen to the bottom. A very fine adjustment must be used, which is why the coarse adjustment screw is implemented.
First of all, one should never call it high power, it is morecommonly called the "high objective", yet that is not what this question is asking. To answer the question: You use the fine adjustment knob. This knob should be located near the coarse adjustment knob, on the opposite side of the microscope (at the same height as the coarse adjustment knob), or even as a separate knob protruding from the coarse adjustment knob. The fine adjustment knob is smaller in size. You should never, ever use the coarse adjustment knob under the high objective, you could scratch the microscope slide, cover slip, high objective lens, or in a worst case scenario break the high objective lens.
The coarse adjustment knob is only used with the low-power objective lens (usually 4x) because all the other ones are too long and the coarse adjustment knob may bring the slide up too qucikly, therefore it might break the slide or crush the specimen being observed. When using the medium (10x) and high (40x) power objective lens, it is best to use the fine adjustment knob to focus on the details instead.
Parts of a microscope are ocular lens, low power objective, nose piece, objective lenses, stage clips, light source, body tube, coarse adjustment, arm, diaphragm, eyepiece, base, stage, fine adjustment, mirror, stain, and high power objective.
The high power objective lense will most likely break the slide. You need to use coarse adjustment on the low power objective lens.
*Draw tube *Body tube *Coarse adjustment *Fine adjustment *Revolving nose piece *Dust shield *Stage *Stage clip *Intimation joint *Base *Arm *Low power objective *oil immasion objective *Condenser *Mirror
Coarse Adjustment
I assume you would use the fine adjustment knob for high power objectives.
For low power you can use the coarse adjustment and fine adjustment for high power you should only use the fine adjustment because on high power, the objective lens is too close to the slide and using the coarse adjustment may scratch the objective lens.
The coarse and fine adjustment knobs can be used with the low power objective.
use the fine adjustment knob to get a better view of what you are looking at.For low power you can use the coarse adjustment and fine adjustmentfor high power you should only use the fine adjustment because on high power, the objective lens is too close to the slide and using the coarse adjustment may scratch the objective lens.
use the fine adjustment knob to get a better view of what you are looking at.For low power you can use the coarse adjustment and fine adjustmentfor high power you should only use the fine adjustment because on high power, the objective lens is too close to the slide and using the coarse adjustment may scratch the objective lens.
The course adjustment moves the stage of the microscope further/closer away from the objective lens (it is used for general focusing), and the fine adjustment moves the objective lens very small distances for finer focusing.
First of all, one should never call it high power, it is morecommonly called the "high objective", yet that is not what this question is asking. To answer the question: You use the fine adjustment knob. This knob should be located near the coarse adjustment knob, on the opposite side of the microscope (at the same height as the coarse adjustment knob), or even as a separate knob protruding from the coarse adjustment knob. The fine adjustment knob is smaller in size. You should never, ever use the coarse adjustment knob under the high objective, you could scratch the microscope slide, cover slip, high objective lens, or in a worst case scenario break the high objective lens.
The coarse adjustment knob is only used with the low-power objective lens (usually 4x) because all the other ones are too long and the coarse adjustment knob may bring the slide up too qucikly, therefore it might break the slide or crush the specimen being observed. When using the medium (10x) and high (40x) power objective lens, it is best to use the fine adjustment knob to focus on the details instead.
The coarse adjustment because it moves the objective much farther than the fine adjustment knob, and you could hit the slide with the objective and damage the lens and/or the slide.
1: Eyepiece 2: Arm 3: Base 4:Stage 5:Stage Clips 6:Coarse Adjustment 7:Fine Adjustment 8:Low Power Objective 9:Medium Power Objective 10:High Power Objective 11:Mirror or Illuminator 12:Diaphagm
Parts of a microscope are ocular lens, low power objective, nose piece, objective lenses, stage clips, light source, body tube, coarse adjustment, arm, diaphragm, eyepiece, base, stage, fine adjustment, mirror, stain, and high power objective.