answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered
2007-11-27 00:44:21
2007-11-27 00:44:21

1) Water has gotten into one of the door lock switches and corroded it.

or

2) GEM module is shot.

001
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


when you open the back door if you look where latch is you should be able to see a rectangle shape hole if you put your key in this and turn it you can activate/de activate the child locks


If there are no blown fuses in your Lincoln ls, then there could be a short in the wires causing your power locks to not work.


The door sensors are inside the door locks. If your door sensor are sticking causing the interior light to stay on. Spray some WD-40 on all the door jams including the tailgate.


what about them? yeah for real, my door locks work pretty well.


On a 1998 Lincoln Navigator : I'm assuming you mean the " 4 L " position on your Control Trac selector dial . The 4 wheel drive LOW position " locks " the transfer case so equal power is delivered to all 4 wheels , it is meant to use off road and the speed is limited ( the last time I used 4 low was to drive out of a snow covered ditch along the edge of a highway )


you might want to check your fuses because one might be blown.


Your Hyundai dealer has to go into the computer and program this option.



Try this: Cycle the ignition from OFF to RUN eight times within 10 seconds, ending in the run position. The power door locks should cycle to indicate program mode, vehicle is ready to accept remotes. Press any button on the remote, once again the locks will cycle to indicate a successful program. Turn the ignition off to exit the program mode.


Door locks are protected by circuit breakers. A surge of power to a fuse would cause it to blow. They are located in the fuse panel.


With the opening up strategy in China going deeply, wealthy and middle class appear constantly and high-grade buildings are developed quickly. High grade electronic intelligent cam locks have extensive prospect of market development. With the investment of Chinese lock industry on high technology of intelligent locks increasing annually and 3G times coming, electronic locks have shown the trend that takes place of mechanical locks.


I had the same thing happen to me yesterday. Today the car won't start at all and the battery is fine. Locks continue to lock and unlock as if the car was possessed. Help would be most appreciated!


Rear Door Child Safety Locks (Sedan and Wagon models only) Child safetly locks are located on the rear edge of each rear door. To activate the locks, you must insert your car key into the opening and turn to the locked "vertical" position. To disengage the child safety lock, insert your car key and turn to the center position.



FIND THE SHORT TO FIX, IT'S PROBABLY IN THE HARNESS IN THE DOOR JAM.


Chances are it is the keypad on the driver's door malfunctioning. I had this happen to my 2001 continental. It affected the locks and also the dome light. Hope this helps. It cost me about 280.00 total to have it repaired


My mechanic found a wire under the driver's side seat that had rubbed bare and was touching the metal underneath and triggering the locks to activate randomly on their own.


I believe a passive alarm will just activate a horn or very loud sound device after the initial trigger is activated, like opening a door, hood or trunk lid. And that is that. You need to get a pricier alarm to activate door locks, etc. Hope this helps.


If you are using the USA version of the game, I created an infinite health code: 021BE25C 000000FA Just activate it and start playing your game; your health bar should never decrease (you don't need to press any buttons to activate the code)


Lift passenger side handle, insert door-key, turn to unlock and then turn a little harder, this will activate a lever which will bypass the deadlocks.


Enter the keyless entry master code, then hit the 1/2 button. Enter your new code. The door locks will cycle to indicate that the code has been accepted.


Graphite works well in lubricating key operated locks such as, pad locks, door locks and ignition locks.



Start vehicle and then hold both lock and unlock buttons on remote for 10-20 seconds, locks will activate and should be programed.


1. Close all doors and then open drivers door and press the UNLOCK button on drivers door panel while door is open and insert key in ignition. 2. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. 3. Within 20 seconds press any button on first keyless remote. Door locks will cycle to confirm programming. 4. Within 20 seconds, press any button on second keyless remote. Door locks will cycle again to confirm programming. 5. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.