Car Sounds
Jeep Grand Cherokee Laredo
Decade - 1970s

Why does your transmission make a crackling noise like crushing metal pieces when you accelerate really fast going up hills?

101112

Top Answer
User Avatar
Wiki User
2005-11-16 22:34:40
2005-11-16 22:34:40

If it's rear wheel drive it could be a U-Joint going bad. If it's front wheel drive it could be a CV joint going bad. That's just a guess since I can't hear the car.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

to grind rocks into smaller pieces

User Avatar

Crushing creates a physical change in the size of the pieces but it does not change their chemical make up.

User Avatar

crushing the rock into pieces and the weathering of the rock.

User Avatar

Crushing an aspirin is a physical change because the small pieces are still chemically the same as the aspirin tablet.

User Avatar

Cracklings are usually deep fried. You may want to remove the skin, cut it into pieces, and deep fry them in lard until they get crispy.

User Avatar

Premolars and Molars are used for grinding, crushing, and chewing. They help break down pieces of foood.

User Avatar

In this case the clove of garlic should be chopped into small pieces, instead of crushing with a garlic press in the normal manner.

User Avatar

Each grasshopper only has one labium. The labium is the lower lip which is involved in crushing food into smaller pieces.

User Avatar

first by blasting- explosives break the rock into small pieces. These are further reduced by mechanical crushing. Crushers are machines that feed rock into jaws or rollers that crush into into very small pieces.

User Avatar

Destroying or crushing the rocks into pieces is a Physical Change, because the molecular formation in a rock doesn't change at all :)

User Avatar

Segmentation is process of dividing data streams into smaller pieces suitable for transmission. This done so it can fit into a transmission control protocol or TCP segment so it does not violate the rules concerning the maximum data amount in a segment.

User Avatar

Digestion of food starts the minute you put the food in your mouth. The teeth start digestion by tearing and crushing food down into smaller pieces so that it will fit down the throat.

User Avatar

A socket set with sizes ranging from 10-18mm, a transmission jack or equivalent (I used a motorcycle jack and 6 pieces of 4x4 dunnage)

User Avatar

No. Crushing results in a fine pulp. Mincing gives you finely diced pieces. The difference shows up when you cook it in oil. Since crushing results a more moist product, it will make the oil spatter more than with the minced garlic. Also, when mixing garlic into other ingredients, crushed garlic distributes more evenly.

User Avatar

squeeze two metal pieces twoards center pull off

User Avatar

1. Pull transmission. 2. Clean transmission case. 3. Take transmission to a rebuilder. 4. Reinstall transmission and be happy. Transmission rebuilds are not for the faint of heart. There's about a million pieces in one, they have to go in exactly right--there's so much stress in a transmission, one part not in right will kill the whole thing--and you need tools you wouldn't buy in a million years. Give this job to someone who rebuilds transmissions all day.

User Avatar

The bag of chips will weigh the same amount as before because crushing them up does not involve adding or removing any of the chips

User Avatar

There are various methods depending on which ore it is. Most start with physically crushing to ore into small pieces. The ore is then exposed to a combination of heat, chemicals and physical processes that result in a liquid molten metal that is poured into ingots.

User Avatar

The sluban pieces do fit with Lego pieces.

User Avatar

An electromagnet can be used a couple of ways. It can be used on the end of a crane, to pick up large pieces of metal to be moved into shredders, or restacked for transportation, crushing, etc. It can also be used to separate metal from non-metal pieces. Usually, these types of magnets are on a conveyor belt, and will cull metal from, say, plastics or other non-ferrous metals such as copper, and aluminum.

User Avatar

Yes. If Reeces Pieces was American, there would be no Reeces Pieces because Reeces Pieces is Reeces Pieces which is the real Canadian Reeces Pieces.

User Avatar

underneath the back end there should be two little metal pieces. pull those out to disengage the transmission. the location varys by model

User Avatar

what is the examples of the elecution pieces what is the examples of the elecution pieces what is the examples of the elecution pieces

User Avatar

If it is an automatic transmission check the transmission fluid level. I assume it has a 4 speed overdrive transmission,if so it could be a broken reverse band or as mentioned by another tech it could also be a bad reverse shell-- which is one of the most common failures of the 4T60E transmission. Usually if the shell is broken you can pull the bottom pan and there will be large pieces of metal on the magnet. good luck

User Avatar

it depends on how big the pieces are if the pieces are 2x2 there are three pieces


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.