answersLogoWhite
Starters and Ignition Systems
Chevy Blazer
Kia Spectra
Nissan 300ZX

Why is Key stuck in ignition on 1990 300zx?

202122

Top Answer
User Avatar
Wiki User
Answered 2007-01-31 18:27:46

The reason the key is stuck is because the shifter linkage is out of alignment. To remove the key just remove the black plastic piece the surrounds the ignition key , use a finger nail file or something similar , it pops out pretty easy , then you will see a little "Red" colored button , push the button in , you now will be able to push the black button in and the key can now be removed. I know I'm a genius !

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Your Answer

Related Questions


There's a button under the the key on the ignition terminal. Push it and pull out the key!


If your 300zx has no power to the entire car and the key is stuck in the ignition you have to press the emergency button located in the ignition. Simply remove the black piece from your ignition.(its a black cap)..and when removed you will see a small red button..if you see that push that and press the "push" black button, turn your key and pop it out.


Key is stuck in ingnition


how to remove key stuck in ignition switch in Chevy colbalt


There is an access cover just under the ignition cylinder. Remove this to remove the stuck key.


Well, it sounds like the chip that is in your key may have broke or got stuck on a part of the ignition. I had that problem. This happened not long after I had had to have the ignition replaced?!?


There should be a lock on the ignition a push button that you push and turn to remove the key


No, the ignition switch is not located in the tumbler assembly. If the key is stuck try turning the steering wheel each way while at the same time turning the key. If it will not come out then something is wrong with the assembly.


To remove a key that is stuck in the ignition on a Peugeot 406 HDI, make sure that the car is in park. Then try to remove the key. If this does not work, spray the ignition mechanism with WD-40 after pulling out the key as far as possible. Then work the key in and out until it comes out.


If the key is stuck in the ignition you will need to get it looked at by the dealer. One temporary solution is to pop off the cap next to the shifter console and you should be able to remove the key by sticking a pen in there.



some low life scum tried to steal my 300zx, and totally f..cuk,d my ignition (key entry) and cant seem to work out the tool i need to remove the old one.. ?????



just flip de key and try again, the key is to old get a new one.


Use the opportunity to replace the ignition. Key needs to be in On position for removal.



The tumblers in the key cylinder have most likely become stuck in the wrong position and you will have to replace the ignition key cylinder.


See You-Tube Video : http://youtu.be/lBNUuO4ldfI How to Remove a broken key from an Ignition. Using the Broken Key Extractor Kit from: www.WedgeCo.com




Wiggle the key as you turn the key while in the ignition switch. My 1994 gets stuck about once a month.


the tumblers have gotten out of sync, you'll probably have to have a new ignition switch put in


your key is probably wore out and tumblers are not moving


light a fire cracker and put it near the point of stuckness, you may need to buy a new ignition system but atleast the key will be out


this is caused by ignition lock cylinder failure, you will have to replace the ignition lock cylinder and key.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.