Why is a 1992 Colt 200E still stalling after the distributor cap rotor fuel filter air filter plugs plug wires changed throttle body cleaned and the fuel injectors have been purged?
I have to answer this myself. I had a diagnostic test at a Dodge dealership. It took them a long time to find the fault, but it was in the distributor itself. Rather than pay 800 dollars, I got an auto wrecker employee to get a used distributor and he replaced it for only 120 dollars including parts and labor. Now my Colt doesn't stall anymore.
Could it be a bad EGR valve if your 1998 Sierra hesitates under partial load and you have changed the air cleaner spark plugs and wires?
yes i now know i first changed oxygen sensor and ran the moter no change then i changed the tps and did minor throttle body cleaning with tooth brush and every day throttle body cleaner and reassembled it fired right up with no accelerator pedal being applied. it cost about 90 bux in all and took less then 2 hrs used just common hand tools.
Was it missing and sputtering before you changed them? If no, then you could have got the firing order mixed on the distributor. Maybe if you didn't replace the wires also one became more damaged while removing it. If yes, maybe its your fuel, or injectors, and you need to add a bottle of cleaner to your gas tank.
1991 acura integra while driving just shut down and didn't start again i changed the distributor and battery n still won't start what can be the problem?
You have a 93 Buick Skylark with the 4 cylinder It codes throttle position sensor changed it twice changed idle air sensor and a used throttle body runs worse still codes throttle position sensor?
You have 2002 mustang it is missing check engine light is on had code checked at AutoZone crank shaft sensor and number 3 cylinder misfiring changed sensor still missing?
1994 F250 460 Engine Low power on higher rmps back fires on deceleration Changed Catalytic converter and throttle position sensor No change low rpm seem oK?
if you changed the distributor cap and rotor it could possibly be your coil or the pick up in the distributor. you have to check and see if the rotor in the distributor turns when you try to crank it over. or you might want to check your timing chain. Answer changed the distributor it was the little magnet that's around the shaft on the inside thankyou JESUS for the help didint get any here…
Why does my Suzuki Samurai stall out after it has been under water. It was turned off and not ran till the fluids were changed the following day?
Did you also completely drain the gas tank and carb? Or if it's fuel injected at least pour a couple pints of 90% isopropal alcohol in the tank and bleed the fuel rail a few times. Injectors cannot inject water. The alcohol will absorb the water and then it can pass thru the injectors. I'm assuming you removed the distributor and completed air dried it.
Your Mitsubishi magna advance is not running well splattering while driving and stalling when you come to a stop and you have changed all plugs and leads?
Injectors typically don't plug too often. The fuel filter needs to be changed routinely. Injectors require a certain amount of pressure to work right. The fuel filter gets dirty and doesn't allow enough pressure into the injectors. Try changing that 1st. Also, the throttle body needs periodic cleaning. I always run injector cleaner once every 3-4 months. If all this fails, you have to pull the injector and be able to apply cleaner/solvent thru it…
If you recently changed the spark plugs on your 2000 Ford Focus and now the throttle is sticking is there any relationship between the two?
I can tell you with relative certainty that the condition and/or operation of the spark plugs should have nothing to do with a sticking throttle. Your best bet would be to check your throttle body for buildup or debris. Also you might check the throttle return spring on the side of the throttle body.
i just changed one this summer on an L300 and you have to replace the whole throttle body it is built in and the only way to get it is to buy a throttle body i have one if you are interested part cost $ 100.00 + shipping not sure what the problem is you are having but most times the codes are not correct if it is giving you running problems and throwing t.p.s…