Chevy Beretta
Ford Explorer XLT
The Difference Between

Why is the transmission of a 91 three one Beretta not shifting until the motor is red lined?

666768

Top Answer
User Avatar
Wiki User
Answered
2009-04-06 19:07:15
2009-04-06 19:07:15

I would start by checking your transmission fluid. it is quitepossible that there is not enough fluid in the transmission causeing this problem, if this is not the case the plates in the transmission are screwed and you need major work done on the transmission or a new one. wolverine I would do a power flush & change the filter B4 spending the cash on a new tranny. i would check to see it there is a out put shaft speed sensor, if there is i would check 2 see if it is plugged in and working

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


The motor mounts hold the engine in place, but to not cause shifting issues. The rough shifting is caused within the transmission system, either electrical, vacuum related, or inside of the transmission.

First guess I'd say your transmission is not shifting into a higher gear.

the beretta and lumina motors are about the same i have a lumina motor in my 95 beretta

The signs of a bad transmission in a Mazda might include hard shifting or a refusal to shift into certain gears. A revving of the motor during the shift can also be a sign of a bad transmission.

I put a 95 Grand Am transmission in my 94 and it works great!!!

It is possible. Replace any broken mount, and this will eliminate the possibility.

There is no such thing as a 1997 Beretta. GM stopped making them in 1996.

moter rocks when shifting

on the transmission between the firewall and motor on top of transmission a few inches from where the half shaft goes into the transmission. if it goes bad it could cause bad shifting of trans, i replaced mine and it was a pain to get out but my transmission problems went away instantly

No, the Camaro is a rear wheel drive, and the Beretta is front wheel drive. 2 completely different engines.

Under the transmission oil reservoir, across from the oil drain plug and on the braking side of the bike. (from bottom of the bike the transmission drain plug will always be on the braking side of the bike. The oil drain plug on the shifting side.)

If the 8th digit in VIN of both cars are the same, then yes.

on the back side of motor by firewall

Seriously? A 305 Chevy motor does not take "transmission fluid"! The transmission takes transmission fluid, and the motor takes oil. The 305 should hold 5 quarts of oil I believe. As for the transmission, I believe that all depends on what transmission you have. Seriously? A 305 Chevy motor does not take "transmission fluid"! The transmission takes transmission fluid, and the motor takes oil. The 305 should hold 5 quarts of oil I believe. As for the transmission, I believe that all depends on what transmission you have.

yes its possible i have a 93 continental i also broke a motor mount (front) witch caused the motor to lift and break open the hood latch and CV joints aswell even causing many problems with wiring harnes / power stering lines / transmission lines the list go's on .....

Talking about for your shifting? The timing is the same as any other transmission, and it really more dependent on your motor and the type of driving you do, than anything. Lot of road drivers are taught to upshift at 1500 RPMs and downshift at 1000. It's a general rule of thumb, and there'll be some variations with different motor types.

The 1997 Ford Taurus has for motor mounts and to transmission mounts. Worn motor mounts and transmission mounts will allow the engine and transmission to have movement.

Shifting up or down is directly related to the rpm. of the motor. It will vary with the motorcycle motor size.

autozone.com if this doesnt work or have the info, call the nearest Chevy dealer

what transmission fits a 455 oldsmobile motor

The sportster has an inter-grated transmission system. meaning that the crank well and the transmission are all in shared space. In order to replace a bad or broken shift for you must pull the motor from the chassis and separate the cases that hold together the transmission. At that point you will need to replace all seals in the motor and consider the condition of the bore and valves. You may actually need some special tools to perform this repair.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.