answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered 2012-05-29 17:30:33

It is just water draining down from the pipes, or sphiphoning out of the water heater. Open both hot and cold taps on the highest sink and the lowest fixture. If the lowest happens to be the toilet, flush it and let it refill. Once should be enough to empty the lines.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Related Questions


Seperate valve for outside faucet turned off, broken valve stem inside of outside faucet or handle stripped at faucet.


The most obvious answer is that the water has been turned off outside the house. Typically, the water dept. does this if there's a billing problem.


You just buy a new one, you can't fix it, cause you turned it on right after picking it from the toilet, which you shouldn't had to do :(



Outer fan cools condenser coil as well as compressor. Even though the cycle is turned OFF the compressor needs to be cooled continuously.


It comes out in November of this year and I can't wait and I just turned 12. (Not sure the exact date though) It premiered April 14,2012 on Nickelodean.


There should be no reason the toilet would overflow. The water being turned off should have no effect on it. As long as the drain is clear even if the shut off valve in the tank didn't work, the water will just go down the drain.




Rotation. Though it does not have to be around a point in the shape: the centre of rotation can be outside the shape.


I assume you mean the water is hot when you flush it. If so the toilet has been plumbed into the hot water system when it should be plumbed into the cold. That happened to me once I thought the toilet was going through menopause, However as it turned out however the hot flushes turned out to be a hot water pipe being connected rather then a cold water pipe.


It is not supposed to be on when engine is running unless there is a problem.


Because of the difference in temperature of the pipe (or the water in the pipe) and the air surrounding it. You could try a foam insulation from your hardware store.


Assuming you have a regular tank toilet with a ball float and rubber flap and that the water is turned on and the tank is filling, the most common cause of a toilet not flushing is a broken or detached chain that runs from the handle lever to te rubber flap that keeps the water in the tank.


the most likely answer to this question is a faulty washer, the reason it keeps running until the washing machine is turned on is cause the pressure is being withdrawn from the toilet. replace the washers to the toilets and monitor. if this fails you may have to consider replacing all the mechinisims inside


Refill tube not connected /working.Float valve stuck or water turned off


The washer in the shut off valve has probably split or come off completely over time.


go to www.humaworm.com and search up parasites on google go to www.humaworm.com and search up parasites on google


bad flapper valve. cheap and easy to replace. check with lowes or home depot plumbing dept. they can tell you exactly what you need and how to install it.


They have probably got air bubbles in them. It may be a worn out ballcock at a toilet.


Usually yes, you have to have them turned off though.


There are temperature balanced shower bodies that will adjust the hot water flow when it senses that the cold water flow drops due to flushing the toilet.


The boy was thinking how desperate he was to go the toilet and then everyone on the bus turned to look at him he realised that he'd said it aloud.



It's something wrong with the pipes! One pipe is on too tight so it whistles when flushing. Here is THE answer!!! I did it to my own toilet. A plumber came over to fix our stuck toilet... The first thing he did was turn off the water supply valve at the back of the toilet. Then he unstuck our toilet. When he left, he turned the water supply valve back on, but he turned it up to high. the water pushes the air up through the pipe and the pressurized air comes out the top little slits on the stopper thingamagigie. To put in words you can understand, it's like blowing a flute. The Fast fix is to do this... Turn the water valve one way and then another. You will know when the water flows faster because the whistling will still be there. What you want to do is SLOWLY turn the water valve to the off position UNTIL the whistling stops and then a little more. You now have water coming in, but not at a speed to pressurize the air and make the whistling sound!



Copyright ยฉ 2021 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.