0
They are, but you must correctly account for parasitic effects.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
What are the differences between analog and RF circuits?
analog circuit is circuit that generates audio, sound, radio etc (waves of the natural world) RF stand for radio frequency, it is often refer to the property of signal transmission in high frequency (HF). If you say a circuit is RF, the circuit would be in the frequency range between 3kHz to 300GHz. The reason that RF circuit is special is because the performance of signals of higher frequency is different to other lower frequency AC circuits. When designing a RF circuit, RF engineers have to consider the type of wires, lengths, use of components, signal loss etc. It is because high frequency signals would take a piece of wire (longer than 1/10 of signal wavelength) as wires with many inductors and capacitors.
Circuit for single tuned amplifier?
A single tuned amplifier basically consists of a tuned circuit (which may consist of an IFT or a parallel tuned LC circuit) connected to the collector of an amplifier circuit (in Common Emitter configuration). The tuned circuit is designed to get a resonant frequency equal to the incoming frequency signal that arrives at the base. The Single Tuned Amplifier gives maximum amplification to that particular incoming frequency which matches the resonant frequency of the tuned circuit and attenuates all other frequencies. Thus it gives sharp selectivity with a high Q-factor.
High pass RC circuit?
Hi pass says it passes higher frequency signals and blocks lower pass signals. This isn't typically a hard cutoff point but the lower frequency signals get attenuated over a frequency range. The R stands for resistance and C for capacitance such that these components are used to create the pass band for the circuit.
What are the limitations of h parameters?
Explain the transient response of an inductive resistive and capacitive circuit for a DC connection
What is high frequency tuned amplifier?
High frequency amplifier is a device which is tuned by high frequency. Tuned means the overlapping of generated frequency with that amplifier.
Why AM is high frequency in communication why not low frequency?
A.m. can be applied to a carrier of any frequency.
Am demodulator diode detector circuit?
demodulator circuit is a circuit which is used for remove all high frequency components from modulated signal.
What is use of RFC in Hartley oscillator?
it is a radio frequency choke which connects the dc supply to the circuit but isolate the dc supply from the high frequency oscillations generated in the feedback circuit
Can you apply kcl and kvl in ac and dc both why?
You can apply KCL (Kirchhoff's Current Law) and KVL (Kirchhoff's Voltage Law) in both AC and DC analysis. It just gets complicated in AC, because now you have to consider capacitive and inductive reactance, phase angle, power factor, etc. Even in a purely resistive circuit, one without capacitors or inductors, you need to consider AC analysis techniques if the frequency is sufficiently high, because of parasitic reactance that is always present. Kirchhoff's laws are the laws of nature for electrical and electronic circuits.
How do you convert low frequency to high frequency with a circuit?
You typically create a DC power supply from the low frequency, and use that to run a high frequency oscillator and amplifier. If there needs to be a relationship between frequency in and frequency out, often there is a divider running on the high frequency side in combination with a phase locked loop synching up to the low frequency side.
Why high pass circuit is called as an Differentiator?
That is its function. An RC low pass circuit is an integrator.
Why is parallel resonant circuit called a rejector circuit?
because at resonance frequency in LRC parallel circuit,impedance is high, so it minimize the current. thus we say its a rejector circuit .
What is the effect of inductance in the circuit?
Inductive reactance is proportional to frequency... XL = 2 pi f L ... so, the higher the frequency, the higher the reactance. At a sufficiently high frequency, the inductor would appear to be an open circuit. Note, however, that at very high frequencies, parasitic capacitance becomes a factor.
Why RC oscillators are not suitable for high frequency generation?
Because an RC oscillator is affected by stray capacitance in the active components in the circuit. HF oscillators use an LC tuned circuit to define the frequency.
What is the effect of inductance in high frequency circuits?
Inductive reactance is proportional to frequency... XL = 2 pi f L ... so, the higher the frequency, the higher the reactance. At a sufficiently high frequency, the inductor would appear to be an open circuit. Note, however, that at very high frequencies, parasitic capacitance becomes a factor.
What is the relationship between capacitance and frequency?
This is a very broad generalization, but in general, increasing the value of one or more capacitors in an electronic circuit will decrease the resonant frequency of one or more sections of the circuit.
What are the differences between analog and RF circuits?
analog circuit is circuit that generates audio, sound, radio etc (waves of the natural world) RF stand for radio frequency, it is often refer to the property of signal transmission in high frequency (HF). If you say a circuit is RF, the circuit would be in the frequency range between 3kHz to 300GHz. The reason that RF circuit is special is because the performance of signals of higher frequency is different to other lower frequency AC circuits. When designing a RF circuit, RF engineers have to consider the type of wires, lengths, use of components, signal loss etc. It is because high frequency signals would take a piece of wire (longer than 1/10 of signal wavelength) as wires with many inductors and capacitors.
