answersLogoWhite

0


Best Answer

The purpose of the 3cm is to avoid danger and our safety.

User Avatar

Anonymous

Lvl 1
3y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Why light a match and hold it just slightly above the top of the burner or about 3 cm above the mouth of the barrel?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you light a Bunsen burner safely?

Lights when the gas flow is small and only then adjust the flow from the source as desired. Also adjust the burner with the rotating the barrel.


Why is in need to light a match and hold it justsxlightly abovew the top of the burner or about 3cm above the mouth?

It place above the the top of burner or about 3 cm above the mouth because for us to avoid the heat of the match, because if you put the match in fire it can cause light/fire.


What is a Bunsen burner splint used in science?

It is used to light the bunsen burner.


Why should you light a Bunsen burner from the side and not the top?

If you light the burner from the top, the lighting instrument will be blowin out by the force of the gas.


How do you operate burner?

You take a match, light it up and turn the knob on the side of the burner.


What is a Bunsen burner and what is it's uses?

From Wikipedia (see Link to the left):A Bunsen burner is a device used in scientific laboratories for heating, sterilization, and many other uses.The device safely burns a continuous stream of a flammable gas such as natural gas (which is principally methane) or a liquified petroleum gas such as propane, butane, or a mixture of both.From ScienceByJones.com (see Link to the left):The Bunsen burner is used frequently in the laboratory as a source of heat. This burner is designed so that gaseous fuel may be mixed with the correct amount of air to yield the maximum amount of heat. In order to use this burner properly and safely, it is essential that you understand its construction and the adjustments that can be made.The three principal parts of the burner are: barrel, needle valve, and base. The quantity of gas admitted to the burner is controlled by the needle valve, while the air needed for combustion is admitted at the small opening around the bottom of the barrel. The air is controlled by turning the barrel so as to make the air holes larger or smaller.Always open the desk outlet valve fully and regulate the gas supply to the burner by the needle valve. Always extinguish your burner by turning off the desk outlet valve (and then closing the needle valve and barrel.) If there is an accident always shut off the desk outlet valve immediately.STEPS TO LIGHT BUNSEN BURNER:1. Check connections to burner and desk outlet valve.2. Close needle valve and barrel.3. Open desk outlet valve fully.4. Check for leaks with flame.5. While holding flame above barrel, open needle valve 1/2 turn.6. Adjust barrel and needle valve for blue in blue flame.Always light burner in open space on lab counter. After you have adjusted it for the flame needed move it into position. One person in lab group is always responsible for maintaining the burner and flame.Burner Procedure:1. Light the burner according to our rules. Observe the yellow flame which is produced because not enough air is admitted to give complete combustion. The yellow color is caused by small particles of unburned carbon which become incandescent.2. Now rotate the barrel until the flame is entirely blue. Two different zones should appear when the burner is correctly adjusted. Too much air should not be admitted as it may cool the flame or blow it out entirely. After having the teacher confirm a good hot, blue flame draw a diagram of the flame (use labels and descriptions). Indicate on your diagram of the flame where the hottest part of the flame is located.See the Web Links to the left for more information.Bunsen burner barrels can be rotated, either opening or closing the barrel, to adjust the flow of air or oxygen, thereby controlling the flame.


When the pilot light comes on when the burner comes on there is a boom?

Think it is just that the pilot light is lighting the main burner, which makes a booming sound.


How do you operate Bunsen burner?

You take a match, light it up and turn the knob on the side of the burner.


What is the same convection and radiation?

light burner.


Burner in a boiler system?

Pilot light


What is a Bunsen burner and its parts and how is it used?

From Wikipedia (see Link to the left):A Bunsen burner is a device used in scientific laboratories for heating, sterilization, and many other uses.The device safely burns a continuous stream of a flammable gas such as natural gas (which is principally methane) or a liquified petroleum gas such as propane, butane, or a mixture of both.From ScienceByJones.com (see Link to the left):The Bunsen burner is used frequently in the laboratory as a source of heat. This burner is designed so that gaseous fuel may be mixed with the correct amount of air to yield the maximum amount of heat. In order to use this burner properly and safely, it is essential that you understand its construction and the adjustments that can be made.The three principal parts of the burner are: barrel, needle valve, and base. The quantity of gas admitted to the burner is controlled by the needle valve, while the air needed for combustion is admitted at the small opening around the bottom of the barrel. The air is controlled by turning the barrel so as to make the air holes larger or smaller.Always open the desk outlet valve fully and regulate the gas supply to the burner by the needle valve. Always extinguish your burner by turning off the desk outlet valve (and then closing the needle valve and barrel.) If there is an accident always shut off the desk outlet valve immediately.STEPS TO LIGHT BUNSEN BURNER:1. Check connections to burner and desk outlet valve.2. Close needle valve and barrel.3. Open desk outlet valve fully.4. Check for leaks with flame.5. While holding flame above barrel, open needle valve 1/2 turn.6. Adjust barrel and needle valve for blue in blue flame.Always light burner in open space on lab counter. After you have adjusted it for the flame needed move it into position. One person in lab group is always responsible for maintaining the burner and flame.Burner Procedure:1. Light the burner according to our rules. Observe the yellow flame which is produced because not enough air is admitted to give complete combustion. The yellow color is caused by small particles of unburned carbon which become incandescent.2. Now rotate the barrel until the flame is entirely blue. Two different zones should appear when the burner is correctly adjusted. Too much air should not be admitted as it may cool the flame or blow it out entirely. After having the teacher confirm a good hot, blue flame draw a diagram of the flame (use labels and descriptions). Indicate on your diagram of the flame where the hottest part of the flame is located.See the Web Links to the left for more information.Bunsen burner barrels can be rotated, either opening or closing the barrel, to adjust the flow of air or oxygen, thereby controlling the flame.


What is the used of alcohol burner?

Alcohol burner, also referred to as backpacker is used to replace a Bunsen burner due to its light weight, simple style and it is handy.