The blades of an axial flow turbine have the aerofoil shape...
Also,for the axial flow turbines... Vf1=Vf2
The water strikes the blade surface at the same time from the root to its tip and a stream of water will leave the water at the correspondin trailing edge.
Therefore,for inlet to outlet,the radius and blade velocity will be the same,BUT the blade velocity will be different at different sections of the blade due to variation in the radial distance,which implies that the velocity triangles for each section of the blade will be different.In order to achieve shockless flow,the inlet and outlet triangles of a blade must vary from root to its tip,and therefore,axial flow turbine blades are twisted...
shroud effectively prevents flow leakage thus reducing losses in the turbine.
Ljungstrom Turbine is a Radial Outflow Steam Turbine with two counter rotating discs. Blades are mounted in circles one bigger than the other. Blades of one rotor work as nozzles for the other rotor blades. This turbine design is very forgiving on wet steam. It is said that the turbine design had limitations on scaling up above 30 MW and hence could not compete with Axial Flow Turbines.
Centrifugal force of the fan results in an increase in static force. The blades of the axial flow fans force air to move parallel to them.
In axial flow compressors, the primary purpose of IGVs (fixed or variable) is to guide the airflow onto the first stage rotor blades at an appropriate or required angle of attack.
in a radial flow turbine the steam enters the turbine in the direction of its radius and leaves it in the direction of the axis of the shaft. in a axial flow turbine the steam enters the turbine in the direction of the axis of the shaft and leaves the turbine in the same direction.
See the Wikipedia article linked below
These are machines dealing with fluids, like (Axial Compressors, pumps and Fans). the term "Axial" is given due to the direction of inward and outward flow. In axial turbo machines the direction of outward flow is the same as the direction of the inward flow since the blades of the machines doesn't change the direction of flow.
The centrifugal flow compressor has a single or two stage unit using an impeller. The axial flow compressor is a multi-stage unit using alternate rows of rotating (rotor) blades and stationary (stator) vanes.
It happens because the Sun heats the ground in the daytime and that heats the air above, which causes winds to flow and drive the blades of the wind turbines.
David Rosenbaum has written: 'Sasha's trick' 'Computer program for generating input for analysis of impingement-cooled, axial-flow turbine blade' -- subject(s): Fluid dynamics, Transmission, Turbines, Heat, Data processing, Computer programs, Jets, Blades
Turbines don't produce energy. They convert combustion from burning gas or water flow. A turbine is just a device with a lot of blades that convert water flow or gas flow to rotation. This rotation then turns an electrical generator, interfaces with a power take off unit, or provides jet thrust.
Ljungstrom Turbine is a Radial Outflow Steam Turbine with two counter rotating discs. Blades are mounted in circles one bigger than the other. Blades of one rotor work as nozzles for the other rotor blades. This turbine design is very forgiving on wet steam. It is said that the turbine design had limitations on scaling up above 30 MW and hence could not compete with Axial Flow Turbines.
Rodney Loren Bown has written: 'An investigation of the secondary flow phenomena in a cascade of high-deflection axial-flow impulse turbine blades' -- subject(s): Aeronautics
Centrifugal force of the fan results in an increase in static force. The blades of the axial flow fans force air to move parallel to them.
the turbines turn as a result of the flow of water
the frontal area of a centrifugal compresor is more as compared to axial flow compressor for a given air flow. And for this reason axial compressors are being used in aircraft engines.
Axial flow pump has high specific seed. According to US unit Ns >10000 has Axial flow pump.
In axial flow compressors, the primary purpose of IGVs (fixed or variable) is to guide the airflow onto the first stage rotor blades at an appropriate or required angle of attack.