Quantcast
answersLogoWhite
notificationBell

Top Answer
User Avatar
Wiki User
Answered 2005-08-31 03:50:25

The only thing common to all those lights (but not to the center brake light) is the hazard switch. I'd check that next. On my 96 Century the hazards override the signals and brake lights meaning that the signals and brake lights must be wired into the hazard switch somehow.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Still Have Questions?

Related Questions

Why do your turn signals and hazards not working?

fuse or blub is out or blown, or wiring is bad, or the relay is bad.


How do you fix the turn signals on the early version 2001 Passat?

If the turn signals are inoperative check the hazard switch, if the hazards don't work replace the hazard switch, the signals will start working. if the hazards are ok ,the turn signal switch may be bad.


What would cause the Turn signals to quit working and all other lights work hazards work also Changed turn signal switch this is for a 1988 GM sierra and Checked all fuses and flasher uit?

Blown fuse or bad flasher unit. Often, cars use different flasher for the turn signals and the flasher, so it is possible for the hazards to work and not the turn signals.


Why do your turn signals and hazards not working on my 2003 intrepid?

More than likely the flasher relay is defective, replace it.


Why are Hazards working but indicators not flashing on Audi tt?

It contains two relays, one for hazard lights and the other for turn signals. The one for the turn signals is defective and must be replaced.


How do you fix HazardTurn signals that are not working in 1995 Volvo 850 T5-R?

Well so far I have found that when I turn my headlamps on and switch to the high been and then use the rocker switch for the hazards, it will allow for my turn signals to start working again.



99 ford e-150 the hazards and turn signals stopped working suddenly it isn't the fuse for the turn signals or Hazards as i checked what else could it be?

your fuse is to strong try a lower fuse or some other one is wrong sending too match power that why to blows, or is your headlight cracked?



What causes all turn signals and hazards to stop working all at once?

First check the flashers fuse .Then replace the flasher with a good one. There might be two-one for turn signals and one for 4ways. Or they could be one.


My hazards work but turn signals dont in a 1987 acura integra checked the fuses and the relay but still not working?

It could be the turn signal bulbs, some vehicles use separate bulbs for the hazard and turn signals. It could also be a bad switch or wires for the turn signals.


My 87 Honda accord brake hazards and signal lights stopped working I changed signal and brake light fuses the brakes lights are working but not signal and hazards.?

Probably the flasher unit needs to be replaced. This is an electronic switch which usually mounts underneath the dashboard.


Can the hazard switch keep the turn signals from working?

Not typically. answer yes the hazard lights stop turn sinals from working there are only 2 elements in the bulb one for stop and one for turn hazars use same eement as turns signals it is for that reason that it is illegal in most states to actually drive with your hazards working they are supposed to be used only when stopped


Why is your turn signls not working when your hazards work in a 1984 ford f250?

Could be: Fuse Flasher Switch in column There is another flasher behind the fuse panel that controls the signals


1996 Pontiac Sunfire Horn doesn't work can hear relay click and Rear Hazards don't work but turn signals do Why?

Your turn signals and hazards use separate flashers. Your hazard flasher might have bitten the dust. FriPilot sounds like the horn/horns arent working. also sounds like the hazard switch is inop



Your 1988 Fox hazards are working but the flashers don't want to work?

Make sure the 4 way hazard switch is COMPLETELY off, if it is slightly depressed the turn signals will not work.


Turn signals quit working all other lights work hazards work also Changed turn signal switch this is for a 1997 Buick Lesabre Checked all fuzes and hazzards are ok can not find signal relay?

The flasher relay is in the hazard switch. The hazards work on my wife's S4 but the directionals don't. I found another posting that says that the relay is in the hazard switch. The fuse is fine.





Turning signals not working but the hazards do so what could be the problem?

I have found that moisture can cause that problem you may also want to check your fuse and bulbs if you see moisture try to get it as dry as possible


Why are 1994 Geo Metro turn signals and hazards not working?

If you haven't checked the fuse box do so, it's under the dash on the drivers side. If the fuse isn't blown, don't know


Why won't your turn signals work?

There are a number of reasons that your signals might not be working. First off, I would check your fuses to make sure none of them are blown; next, check your bulbs. If those are all okay it might be your turn signal relay--in many car models these are located around the fuse panel somewhere, although they may not be immediately visible--also check to see if your hazard lights are working--if they are, and your fuses and bulbs aren't burnt it's probably your signal relay (note: there is one for the hazards and one for the turn signals) If your hazards and your turn signals are not working you may have a more in depth electrical problem, or both relays could be blown--however unlikely. One of the last things I would look at is the actual switch in the driving column that turns on your signals.



Still have questions?

Trending Questions
Unanswered Questions
What plug replaces l8rtc? Asked By Wiki User
Who are perceptual region's? Asked By Wiki User