Clean the throttlebody and automatic idle controller, which is a black plastic thing directly under the throttle body housing held on by 2 screws, with carb cleaner and a lint free cloth. Start the vehicle and let it idle for a few minutes. When you removed the battery the computer lost its idle memory and you have to clean the throttle body to make it work. Or you can pay an out ragous price for about 15 minutes work Clean the throttlebody and automatic idle controller, which is a black plastic thing directly under the throttle body housing held on by 2 screws, with carb cleaner and a lint free cloth. Start the vehicle and let it idle for a few minutes. When you removed the battery the computer lost its idle memory and you have to clean the throttle body to make it work. Or you can pay an out ragous price for about 15 minutes work
replace it just like any car battery
3 in a little black box in front of the battery.
unhook the battery for about 10 min. should reset
Check your battery post to make sure u have a good connection
Yes, as long as it fits the space and the terminals are oriented correctly.
we just call manufacture and gave em vin numbers they gave us the code
you pop the hood and behind the battery slighty to the left you find a small red cable, carefully pull it off and bam!
how to replace a mitsubishi endeavor battery
Is the battery dead? Check for 12v on the main alternator cable. If no power, check for burned out fusible links between alternator and battery. You may need a wiring diagram to check further.
There are two fuse boxes on the montero. The high amperage fuse box is located under the hood, near the battery. The other, interior fuse panel is located underneath the driver's side of the dash board on the left side of the steering wheel.
Disconnect the battery cables, remove the spark plug cables and covers, and remove the old spark plugs. Next, put in the new spark plugs, attach the covers and spark plug cables and reconnect the battery cables.
Deactivate the battery
You might have the codes located in your owners manual. If you dont, then try calling Mitsubishi and ask them for codes or where you might find them. I know when I take the battery out of mine the radio requires a code and you only get three tries to put them in otherwise you have to take the battery out then put it in again. Hope this helps. Patrick
The yellow fuel dispenser is an indication that your fuel is running low. The red battery is an indication your charging system is malfunctioning. The red water symbol is an indication your cooling system is malfunctioning.
disconnect the battery for a couple of minutes, if it comes back on after you drive the computer is getting an error code from the engine check the codes to see whats causing it
A Montero may not start if the battery is dead or power is not reaching the starter. Both can be readily diagnosed by a local mechanic or dealership.
Disconnect the battery. Warning: If you disconnect the battery for an extended period of time, the radio will not work and you will need to enter a security code to get the radio to work again. The dealership will charge you $$ to supply you with the security code.
To reset the change oil light on a 2008 Mitsubishi Lancer after changing the oil, a person can turn the key to on, but not start, and pump the gas pedal three times, then turn the key off. If this method does not work it is possible to disconnect the battery for a few minutes, then re-connect it.
Replacing spark plugs is pretty simple. Disconnect the battery, remove the cover and cables, remove the old spark plugs, put in the new spark plugs, put the cover and wires back on the spark plugs, and reconnect the battery.
do you have to reset computer after changing battery in 2003 745li
I had this same issue. Take out the radio and call a Mitsubishi dealer. You will need to serial number, and they can look it up on some site they only have access to. Blame the oil change people for leaving the air filter sensor unplugged when starting the car, then having to unplug the battery to reset the check engine light.
Follow the + battery cable from battery should connect to starter solenoid (relay)
Below the battery
Simply unplug the battery and replace the cords to the battery!
Not necessary. No problems will be encountered when changing the battery.