answersLogoWhite

0


Best Answer
Copy

grease cables!

User Avatar

Wiki User

โˆ™ 2005-03-30 02:07:02
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: Why would the RPM gauge on a 1996 Ford Mustang GT 5 speed not respond unless you start out fast and then it will jump up all of a sudden?
Write your answer...
Submit

Related Questions

Why doesn't fuel gauge work on 2005 mustang?

why does the fuel gage on 2005 mustang don't work?


What causes the Coolant gauge to fluctuate on 1994 Ford Mustang?

Temperature.


Why is your gas gauge fluctuation all of a sudden?

A faulty fuel gauge sending unit in the fuel tank could cause that.


How do you fix the RPM gauge on a 1993 Ford Mustang that stays at the six mark?

replace the printed circuit board behind the tach gauge. $15.00


How do you test fuel pump in the tank 3.8 mustang?

You will need a fuel pressure gauge. Connect the gauge to the fuel rail and start the engine. The gauge will tell you how much pressure they pump is putting out.


Why doesnt your temperature gauge on your 1995 ford mustang work?

What are you talking about? My temperature gauge works fine. Though, if it wasn't I would check the temperature sending unit.


Why doesnt my 1994 mustang temp gauge work?

The problem could be a dirty sensor or the sender is no good.


1966 mustang problems with fuel gauge?

Fuel sender inside the gas tank may be block


Does a v6 Ford Mustang 1997 model have a low fuel light?

I was looking at the 1997 Ford Mustang Owner Guide and it doesn't show a low fuel light in the gauge cluster


Why is your fuel gauge not work on your 1993 ford mustang?

id say either a bad ground to chassis on the fuel sending unit (off the top of the tank.) or a bad gauge


What instrument measures gas pressure?

manometermanometerA pressure gauge ...unless you call it a tire gauge.manometer


Why doesnt your fuel level gauge work for your 1990 ford mustang?

The float in the fuel tank may need to be replaced.


Is gauge a man?

no he is not unless he is suposed ti have boobs!!!! just kidding!!!


What is wrong if the temperature gauge will not work and the cooling fan stays on all the time on a 1996 Mustang?

could be the temperature sending unit


Why does your amp gauge go down when you turn on your lights?

The amperage gauge will go down when you turn on your lights, because there is a sudden draw of electric power from the battery. The alternator should equal out the power surge.


What could cause the temperature gauge on 1965 mustang 289 to read cold all the time?

I had the same problem with my 1970 mustang. First take the wire off of the Temperature sending unit (usually on the front of the block) and ground out the wire and see if the gauge goes up on the dash. if so it is just a temperature sending unit. They cost about 7 dollars.


How do you put freon in a 1994 mustang?

Connect a Freon gauge and Freon to the low side ac port. With the engine running and ac on high, open the valve and allow Freon to flow until the gauge reads full.


What is age of Remington 12 gauge serial number 433081?

Go to Remington's website and send the info to them. They will respond in a day or two.


Will a 2003 Toyota Echo cut off if the gas gauge brakes?

Not unless you have run out of gas.


What could be wrong if the gas gauge speedometer and tachometer do not always work on a 2001 Ford Mustang?

It could just be broken. Or the gadget in you gas tank has been displaced


What does the fan dashboard icon on the 1996 Ford Mustang gt indicate?

The low coolant warning light is just to the left of the bottom of your engine oil pressure gauge


Wire gauge for 2amp load?

18 guage will do you ok unless you need to run it a mile or two.


Where can you buy ammunition 9mm and 12 gauge?

why would you be asking this question unless your a police officer and or hunter


How do you repair dashboard lights in a 1973 Ford Mustang?

take off the upper 3-4 screws on dash/gauge panel (attaching to dashpad from below), remove panel, remove press clips holding gauge lenses to gauges (optional), then remove the four - five mounting bolts holding gauge assembly, replace bulbs which are accessed on the rear of the gauge assembly, replace in reverse. good luck.


What will happen if you use knitting needles that are larger than the yarn instructions call for?

Your gauge will be different and the size of the garment will be different, unless you accommodate the larger needles with a new gauge, and recalculate the fit.