answersLogoWhite

0


Best Answer
Copy

Probably because of a BAD ground. If you have 12 Volts to the light, then the light isn't grounded properly. yes sir bad ground

User Avatar

Wiki User

โˆ™ 2006-12-18 00:25:38
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: Why would the rear brake light which is so dim you can hardly see it not get any better after replacing the bulb several times?
Write your answer...
Submit

Related Questions

Why do brake pads squeak after replacing pads?

Why do brake pads squeak after replacing pads?


Passengerside Brake line diagram for a 91 mercury topaz?

If you are replacing the brake lines ( metal ) then just use your better judgment. They do not have to follow the original route.


Why is your E Brake light on and you have hardly any service brake on your 1973 Ford pickup?

probably low on brake fluid


Brake pads Oldsmobile cutlass sierra?

The brake pads on an Olds Sierra are a wearable part. When replacing brakes it is better to change both fronts or both rears at the same time.


Brake lights will not turn of in vectra?

the switch on brake pedal is faulty and needs replacing


Why do brake calibrators need replacing?

brakes do not release


Will leaking brake likes make a truck idle rough?

NO.... Not hardly.


Why do a 1997 Trans Am wheel squeek even after replacing brakes and discs?

Try replacing your brake calipers.


What causes Grinding sound from rear of car when you brake?

brake shoes or pads are worn and need replacing


In what situation is drum brake better than disc brake?

In case of cost..drum brake is better than disc brake.


Can I just replace my brake pads?

Yes you can replace your brake pads but it would be cheaper if you wait until you need a new rotor. I recommended waiting because its way better than replacing it before you need a new rotor.


Why do brake lights in 1965 mustang stay on after replacing the master cylinder?

you forgot to plug in the brake fluid sensor.


What does the brake bulb light mean on a 2004 Honda Pilot?

The "BRAKE BULB" light means that a brake bulb is not working and may require replacing.


How do you put brake drum back on after replacing brake shoe hard getting back on?

Back off the self adjuster and the e-brake adjustment.


Replace brake replace brake light 1995 blazer?

Your brake light is probably brake fluid low or emergency brake on. Rear brake lights are replaced by removing the lens and replacing the dual filament bulb.


Why is there a Screeching sound when brakes pressed?

Brake pads have a wear indicator to let you know when they need replacing. The screeching means you need to replace the brake pads, and the sooner the better to avoid damaging your rotors (the shiny disks that the brake pads rub against to slow your car down).


One brake light doesn't work?

Start with replacing the bulb.


What bulb needs replacing for a Dodge Intrepid brake light?

3157LL


Can you put new rotors on without replacing brake pads?

Yes.


Car makes a loud grinding sound when you brake?

"Could be many things, but from my experience, brake pads might be worn thru and are scraping metal to metal. If so brake pads need replacing. If brake pads are worn thru and not replaced, scoring damage could be accumulating on the brake disc." It could also be due to a warped or damaged router that would be the big metal disk. but if replacing your brake pads doesn't fix the problem replacing your router will more then likely take care of the noise.


How much should replacing brake rotors cost on a Chrysler Pacifica?

Replacing brake rotors on a Chrysler Pacifica will vary in price depend on the labor cost. The price should be around $150 dollars.


How do you replace front brake pads?

Replacing Brake PadsThis will depend on the vehicle. Try asking a more specific question. brake pds 2006 1500


How do you bleed the brake lines after replacing brake pads on a dodge Dakota?

If you did not open any brake lines and only replaced the pads there is no need to bleed the system.


Why do tail lights stay on after replacing brake booster on a 03 Chrysler Sebring?

It is probably the brake lights that are on due to a misinstalled or damaged brake light switch.


Why would the brake lights not work after replacing the bulbs?

Check your fuse box, Your brake fuse is most likely blown.