Car Fuses and Wiring
Dodge Caravan
Mazda 626

Why would the windshield wiper fuse blow as soon as the ignition switch is turned on in a 1993 Mazda 626 dx and how can this be fixed?

121314

Top Answer
User Avatar
Wiki User
Answered
2012-01-22 10:06:44
2012-01-22 10:06:44

try disconnecting the wiper motor if problem still happens disconnect the wiper switch, if that does'nt work check your wiper control box, a fuse will only blow if there is too much current drawing on it or dead short to earth. try and follow the wires back from the wiper motor check for any damaged wires

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


How to remove ignition switch on a 91 Mazda Navajo

Just push it a few feet with the ignition switch turned on and pop the clutch.

The ignition switch on a 1995 Mazda pickup is changed by partially removing the steering column to reveal the switch on the side of the column. It can then be unbolted from its mounts, the wires disconnected, and a new switch put in place.

2002 mazda ,,gauges are still working after taking out key..any ideas

immobilizer is in the key and pickup ring on the ignition lock

You have to push the key & ignition switch in as you rotate it counterclockwise into the off position !!

plenty of things could be a starter, alternator, ignition switch, bad spark...

where is the ignition module located on a 1988 Mazda b2200

How do I replace ignition wires on my 98 Mazda 626 2.0L

Can someone please tell me how to hot wire the ignition of a 1991 mazda protege?

was wondering where the inertia switch is on a 1996 Mazda protege

Answer: Most likely battery (you probably surmised this already), however, it could also be a faulty ignition switch or poor connection at the starter or starter module/relay. When the key is turned, do the instrument cluster warning lights come on (& dim slightly)? If so, its not the battery.

Where is the igniyion coil on a2002 mazda protege

How do I adjust a stoplight switch on my mazda 626 LX V6

You will have to determine if the fuse, the switch, the wiper motor, the linkage, the pulse board or the wiring/connections is at fault before you can fix it.

If you remove the outer case of the steering collum the you will see a whole on the bottom going into the ignition switch, you must insert a thin rod a little bigger than a paper clip but sturdy enough not to bend. insert the key in the ignition and turn the key as you are pushing on the rod and the switch should slide rite out. to put the new one in, just reverse these directions. i did mine in about 5 minutes.

A bad battery terminal(s) connection, bad ground, bad ignition switch, bad starter.

the a\c clutch for the compressor is probably staying on when you turn the car off. It could be the ignition switch. or a bad relay.

On a 1981 MAZDA 626 (same engine)2.0 you remove the right/left cover on the steering column (three screws) and remove them. On the left side behind the key cylinder is the disc (round) ignition switch with several wires attached in a circular pattern around it. Wires and connectors (believe 4) go down the steering column from it (this is the ignition switch). The part # is Niehoff LC62411 on my 626. You remove this and install the new part in it's place. Problem is finding the part. Get one from a junkyard if nothing else. Also, the 82 Mazda truck is the same as an 82 Ford Courier (so maybe a Ford dealer has the part). Ford owns about 30% of Mazda and a Ford VP runs it.

i put a new windshield wiper moter in and the fuses are fine but my wipers still wont work

Yes, at idle it brings the normal stock of 900 up to 1000 rpms

Mazda truck b3000 where is the fuel pump reset switch located


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.