answersLogoWhite

0


Best Answer

Yes, My ignition module was bad, I experienced intermittent stalling. My mechanic replaced and it stopped.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Will a bad ignition module for a 96 S10 pickup make it stall and what does it do?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Can putting a pickup part in the distributor cap help with the engine stalling?

Usually if the pickup goes it won't start. Year, Make, Model, Engine size would help here. Module & coil are popular also. When does it stall? Hot? cold? Idle?


Where is the ignition module on a 1997 Ford Contour?

AnswerThe ignition module is mounted to the front of the distributor. It is a long rectangular piece (about 1"x4") with wires connected to one side. Yes the Ignition module is rectangular piece (about 1"x4) with wire harness connected to it, but some Ford Contour does not have distributor, they have coil park, and some of this car have their ignition module built in the PCM. Year, Make, Model, and Engine size makes a different.


Can a ignition module make a car shake?

If a defective ignition module, (or bad plugs/ wires) causes a misfire condition, one or more plugs won't fire. The uneven power pulses cause engine shaking.


After changing the ignition module on your probe gt still have no spark?

Why start with the module? The coil is is a good place to start. Make sure of course you have voltage at the coil, if not trace it back.


What does it mean when you replaced the cap rotor pickup coil plugs wires and ignition coil and im still not getting spark in a 1996Dodge 1500 with a 318 motor?

Not really sure of the make, but do you have an ign. module? check that. Also any crank sensors. Unless its just a broken wire.


What are the signs if an ignition module going out on a 92 Chevy silverado with a 350ci engine it will crank but not fire but when it fires it runs fine?

after truck warms up will be hard to start,module may even start turning white colored make sure you are getting 12 volts to the module from the ignition also good luck


How do you change an ignition module on a lumina?

the module is under the coils, unplug the wires, unbot all three coils and unbolt the module. Make sure to use plenty of dielectric grease for a good ground


How do you replace an ignition module on an eighty five Chevrolet Celebrity?

The ignition module in a 1985 Chevy Celebrity it located in the distributor. To change the ignition module: 1. Disconnect the ground terminal on the battery. Wear gloves to avoid getting acid on your skin. 2, Remove the distributor cap and place it out of the way. If you pull any spark plug wires make note of where they go so they can be put back. 3. Carefully unlatch the electrical plugs and remove them. The latches are old and brittle, be careful not to break them off. Take note of which one goes where to be able to put them back. 4. The ignition module is held in with two screws, remove them and lift off the module. Use fresh dielectric grease on the replacement module. Coat the bottom of the with a generous amount of dielectric grease. This acts as a heat sink and will greatly improve the life of the module. Reverse the procedure to install the replacement ignition module.


Why would a 1993 gmc sonoma 4.3 gets codes 42 and 43?

I can't make any promises, but I've got 94 Chevy using OBD1, like yours probably has too. In my manual this is what it says: Code 42:Ignition Control Module - "Check the wiring and connectors between the ignition module and the ECM. Check the ignition module. Replace the ECM".Code 43:Electronic Spark Control - "ESC module is not receiving a knock signal from the knock sensor. Check the knock system sensor, or the ESC module. Have the module checked by a dealer service department." Hope that helps, good luck!


Why when your car warms up you loose spark?

Without year make model & engine size you get a guess. Ignition module, coil, distributor


Why does my Gm 2.5l die when hot?

Could be: clogged cat converter bad ignition module bad coil I'd check to make sure cat converter isn't getting red hot when running for a few minutes, if so then clogged. Then I'd replace the ignition module, check, then coil.


Where is ignition controls module?

The control module is located under the hood, sometimes inside distributor,or mounted on outside of distributor, or as a distibutor-less module with coil packs mounted on top or on passengerside fender behind headlight area. All depends on make of vehicle.