0
It will bolt up and work fine. However, if your PCM is for an auto trans (4L60E) , you will get trans trouble codes and vss trouble codes..
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What is 43 percent of 350?
43% of 350= 43% * 350= 0.43 * 350= 150.5
What are the release dates for Power Rangers Turbo - 1997 Parts and Parcel 1-43?
Power Rangers Turbo - 1997 Parts and Parcel 1-43 was released on: USA: 18 November 1997
What is head bolt tighting sequence for 2.2 Chevy 1994 model?
Always start from the center and work your way out. Kind of like in a circular motion but the circle gets bigger & bigger. # Tighten bolt 1 to 63 N·m (46 lb ft). # Tighten bolt 2 to 58 N·m (43 lb ft). # Tighten bolt 3 to 58 N·m (43 lb ft). # Tighten bolt 4 to 63 N·m (46 lb ft). # Tighten bolt 5 to 63 N·m (46 lb ft). # Tighten bolt 6 to 58 N·m (43 lb ft). # Tighten bolt 7 to 58 N·m (43 lb ft). # Tighten bolt 8 to 63 N·m (46 lb ft). # Tighten bolt 9 to 63 N·m (46 lb ft). # Tighten bolt 10 (stud bolt) to 58 N·m (43 lb ft).
Who can run the fastest?
the fastest mile is 3:43
What is the bolt pattern for a 2008 Mitsubishi Lancer 18''inch MAg?
Bolt pattern 5x114.3 offset +43 18x7"
What the difference between a 307 water pump and a 350 water pump?
43!!
What are the cylinder head torque specs and torque sequence on a 01 s10 2.2l?
Tighten the long bolts to 46 ft/lbs. Tighten the short bolts to 43 ft/lbs. #1 is between cyl 2 and 3 (middle bolt, long), pushrod side. 46 ft/lbs #2 is middle short bolt. 43 ft/lbs #3 is short bolt between cyl 1 & 2 43 ft/lbs #4 is long bolt between cyl 1 & 2 46 ft/lbs #5 is long bolt between 3 & 4 46 ft/lbs #6 is short bolt between 3 & 4 43 ft/lbs #7 is short bolt at front 43 ft/lbs #8 is long bolt at front 46 ft/lbs #9 is long bolt at rear 46 ft/lbs #10 is short bolt at rear 43 ft/lbs "After this, (using torque angle meter) tighten in same sequence another 90 degrees."
What is the bolt pattern for a 2000 Chevy Malibu wheel?
5x115 43 offset
What is the bolt pattern on a 1971 Chevrolet Chevelle?
43/4 X 5
Are parts available for a sears bolt action 22 cal model 43 model 1032850 and what is its value and manufacturer?
I am also looking for parts for a J.C.Higgins 22 cal Model 43. I need the complete bolt assembly!
What is the torque sequence on a 98' S-10 2.2cylinder head?
Use the following sequence in order to tighten the cylinder head:Tighten bolt 1 to 63 Nm (46 ft. lbs.).Tighten bolt 2 to 58 Nm (43 ft. lbs.).Tighten bolt 3 to 58 Nm (43 ft. lbs.).Tighten bolt 4 to 63 Nm (46 ft. lbs.).Tighten bolt 5 to 63 Nm (46 ft. lbs.).Tighten bolt 6 to 58 Nm (43 ft. lbs.).Tighten bolt 7 to 58 Nm (43 ft. lbs.).Tighten bolt 8 to 63 Nm (46 ft. lbs.).Tighten bolt 9 to 63 Nm (46 ft. lbs.).Tighten bolt 10 to 58 Nm (43 ft. lbs.).Use J36660-A to tighten all the cylinder head bolts an additional 90 degrees in sequence
How much horsepower does a 1995 stock 350 stock engine have?
it has 43 horsepower stock
