0
Will it cause water to leak down the pipe below your unit if yiu have a loose tiles and grout?
Wiki User
∙ 12y ago
Yes.
Tub or shower water entering the wall through loose tiles or grout can run down the pipes, through the holes the pipes are going though, and into the unit below.
It is more common for water to get into the unit below from leaking shower doors or poorly used tub/shower curtains that allow water to leak out the face of the tub/shower. It then enters the gap where the tub/shower meets the floor, then builds up on the sub-floor, and eventually into the unit below.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Can ceramic tiles become loose if no grout is applied?
No it shouldn't, but you should still grout your tile.
What are some causes for water to seep up through the grout in between tiles on a tiled floor?
Water seeping up through the grout in between tiles on a tiled floor can be caused by several factors, including: Cracked Grout: If the grout between the tiles is cracked, water can seep through the cracks and reach the subfloor. Loose or Damaged Tiles: Tiles that are loose or damaged can allow water to seep through the gaps and reach the subfloor. Poorly Installed Tiles: If tiles were not installed correctly, with inadequate adhesive or a poorly leveled surface, water can seep through the gaps and reach the subfloor. High Water Table: If the area where the tiled floor is installed has a high water table, water can seep up through the grout. Plumbing Issues: A leak in the plumbing system, such as a damaged pipe or loose fitting, can cause water to seep up through the grout. Flooding: If the area where the tiled floor is installed experiences flooding, water can seep up through the grout and reach the subfloor.
How do you clean in between tiles?
Grout.
What grout cleaner can get out mould from around bathroom tiles?
I have a lot of mould around my bathroom tiles and don't seem to be able to get it out from the grout in between. What grout cleaner will work best for this?
Should the grout for a tile floor match or contrast with the tiles?
Grout should usually be white or contrast with the tiles, but it truly depends on your preferences.
What type of grout for bathroom tiles?
if your grout line is less than 1/4" you use smooth grout, above that you use sanded grout.
How do you fill with grout?
First you lay out all the tiles with spacers adhering them to the floor, then you grout between by scraping across surface of tiles. Then just wipe clean. The grout is like a concrete mix & will harden.
Why floor tiles have some gap at the middle?
Ceramic tiles have a grout "gap" but vinyl tiles shouldn't have a gap.
How can you fix tiles that are rough and cause injury without removing the water from your pool?
Removing the tiles and old grout is a dirty and difficult job with the water still in the pool. It has been done. It is just as difficult to install the new tiles & grout. I have of some doing it from inside a small boat in the pool with the water lowered. Have heard of others doing from the deck working up side down, if you will, to set the tiles.
What grout is used for floor tile?
Most often, sanded grout is used for floor tiles because the grout lines are usually greater than 1/8" wide. Sanded grout is necessary for the wider lines to give added strength, and to keep your grout from cracking and chipping out. Unsanded grout must be used if your grout lines are narrower than 1/8", because the grains of sand in sanded grout could cause air pockets and prevent good adhesion to your tiles - and it will crack and chip out as well. Sanded and unsanded grouts are cement-based. One alternative grout on the market is epoxy-based. It is neither sanded nor unsanded, but will work fine in either narrow or wider grout lines. If your grout lines are wider than 1/2", or if you are using saltillo tiles, you must use saltillo grout. Other grouts will not handle this wider width.
Working With Grout During Tile Projects?
One of the most important components of any tiling project is grout, a soft adhesive material that is used to fill in the seal joint spaces in tiles. When applying grout in between the tiles, the right type of trowel is needed to create the patterns that will match the back and side surfaces of the tiles. After the grout dries up, it is important to immediately sand the tiles and apply sealants. The sanding process can be done with standard sanding paper. Additionally, a soft moist sponge should be used to wash any excess grout from the top surface of the tiles. The sealant will help prevent dirt from accumulating in between the tiles.
How do you clean grout off rough tiles after laying down tiles?
there is a special cleaner at lowes in the cleaner isle.
