0
No, thank you.
Wiki User
∙ 6y ago
Add your answer:
Earn +20 pts
How much dirt in a rectangular hole 4 ft wide by 6 ft long by 12ft deep?
There is NO dirt, it is a hole! If you want to fill it with dirt, that is 4x6x12=288 cubic feet, weighing about 28,800 pounds
How do you measure the distance between two holes for drilling purposes?
you are concerned with marking and drilling the the center of the hole. Make a + mark where you want the center of each hole. You can punch the center of that mark with a nail to help the bit stay in the middle.
If a degree is negative is it a monomial?
Depends if you like bananas... JK, no the degree cant be negative because if it was then the trioxians of the neutrino would implode to a sub zero quantum ordinate and the multiverse would incenerate itself and turn into a meca black hole...and that is why we dont want monomials to have a negative degree.
Can you change your earings 3 days before 6 weeks?
You will be able to change it, but it'll be a risk your going to have to take. If you were to change earrings, you might have itching and tiny ball-like swelling on your ear hole which is only temporarily for 2 months. If it lasts over 2 months, you may want to check with your doctor.
What happens when you shine light at an angle toward a mirror?
so it is the same when you put a maginifing glass up to a leaf- you make sure that the dot is as small as can be and you will have a hole in the leaf! so this happen by you focusing all the light on spot that you want to burn - remember light gives off heat (same happens when youshine light at an angle toward a mirror)
What does a knock out bar for a mini lathe do?
The headstock of a lathe is pushed into a tapered hole in the head spindle. It gets stuck in there in normal use, and you cannot pull it out when you want to change it. So . . . the spindle is hollow all the way through the lathe head. To get the headstock to lossen you insert a round knock-out bar into the front of the spindle until it touches the back of the headstock. A few taps with a mallet will jar the headstock loose. Then you remove the knock-out bar.
Wood Lathe?
form_title= Wood Lathe form_header= Make woodworking easy with a wood lathe. What is your maximum budget?*= _ [50] Do you want a portable wood lathe?*= () Yes () No Are you replacing an old wood lathe?*= () Yes () No
How much does a wood lathe cost?
It will cost about 85 to 200 dollars it depends on what you want on it.
How do poles of the spindle differ from those of the onion root tip?
I want to know the same question too
How do the poles of the spindle differ from those of the onion root tip.?
I want to know the same question too
Make a hole in muffler?
you want to make a hole in a muffler or you want to patch one up. Make a hole you can use a drell patch a hole best use sheet metal and rivets then muffler puddy around that
Can you drop a 4X4 Chevrolet Colorado?
While it is possible with a spindle drop....Why would you want to drop a 4x4 truck?
What are the differences between the new lathe and the old lathe?
I'd have to see the two lathes to tell you, but there are four main reasons a turner replaces his lathe: the new one vibrates less, the new one is larger either in length or in the diameter of the piece it can turn, the new one has a bigger motor, or the new one runs at a slower speed than the old one. You're asking yourself "wouldn't you want a faster lathe?" No! A turner wants a lathe that has lots of power at slow speeds because it's safer to make the initial cuts on a piece at a really slow speed, and the slower speed will let you make turn larger pieces.
What size hole needs to be drilled for a 0.375 screw?
You want a .375 hole. +.001, -.001, maybe.
Who said What do you want me to do Summon the snake out of its hole?
Leafpool
Driver wiper not going all the way back down?
Pry the arm off the spindle and reposition it a couple of teeth in they direction you want it to stop. There are usually around twenty teeth on the spindle so you can really fine tune the adjustment relatively easy.
My ears were pierced but they've closed up can you get the same 'hole' re-pierced or will I have to have a 2nd hole?
Yes you an have the same hole pierced. But make sure that is where you want the hole this is a second chance t get them perfect.
