Best Answer

generally if a crankshaft pulley comes off, it is either thru the rubber bushings in it wearing out and tearing or the bolts came out or sheared off the new pulley wheel will only go back on one way usually with a key to locate proper placement on crankshaft to enable correct ignition timing FYI the crankshaft pulley is called the HARMONIC BALANCE any auto dealer for your make of car can supply proper parts needed

User Avatar

Wiki User

โˆ™ 2007-05-22 12:38:34
This answer is:
User Avatar

Add your answer:

Earn +5 pts
Q: You would like to know what kind of crank shaft pulley your car has it completely came off and you are confused as to how it goes back on It is a 1995 3000 GT?
Write your answer...

Related Questions

How do you take off a crank shaft pulley?

how to get the crank shaft pulley off of a 03 Hyundai elanta GLS

How to check crank shaft pulley?

A video instruction guide on how to check a crank shaft pulley can be seen on YouTube. Just type in "How to check crank shaft pulley", click on Search, then play the first video.

How do you remove crank shaft pulley megane?

To remove a crank shaft pulley you need to first jack up the car. Next, remove the bold holding the crack shaft pulley in place and remove the unit. Reverse direction to put the new crank shaft pulley on your car.

Need to no were timing mark is on crank pulley on 1999 daewoo nubira?

Check the crank shaft pulley

What causes clanking on bottom crank shaft pulley to rattle?

its loose tighten the pulley

What tool do you need to remove a crank shaft pulley?

12mm /19mm

Where is the front main seal on a dodge caravan?

It is on the front of the crank shaft. It seals the oil at the crank pulley.

Where is the crank shaft bearing located?

It's behind the timing belt cover on top of the crank pulley.

Where can you find a diagram of a crank shaft pulley system for a 1994 Saturn?

This what you are looking for?>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>

Is the crank shaft pulley supposed to turn freely?

No, it's bolted to the end of the crank which pistons/rods attached to.

Where is the crank shaft sensor on a 92 Mazda mx-3?

To the right of the crank shaft pulley. You should see a single black wire going up from the pulley. All you need is a 10MM socket to remove it.

Why is there no woodruff key on crank pulley on 5.3 vortec?

The 5.3 liter Vortec Engine on the 2000 Chevy Silverado has a tapered crank shaft. The crank pulley has no woodruff key, is not indexed and is pressed on.

Where are the timmimg marks on a 2001 escort zx 2?

cam shaft pulley mark to head /crank shaft pulley mark to oil pump housing mark

What happens if the cam shaft got turned when replaceing the timing belt how do you reallign?

Align the dot on pulley with the one on the crank pulley.

Where is the crank shaft sensor on a 1994 buick lesabre?

under the crank pulley, right side of car under front of engine

What is the torque setting for the crank shaft pulley on a 350 Chevy engine?

60 ( ft. lbs )

Is a 1996 Isuzu rodeo 3.2 crank shaft pulley bolt left hand threaded?


My crank shaft serpentine belt pulley is about one half inch out of alignment How can this be corrected 1995?

the only way this can happen is if the power steering pump shaft goes bad and forces the belt out of alignment. The crank shaft is ok

Where is the crankshaft position sensor in a 2002 Hyundai Sonata?

It is behind the crank shaft pulley in front of the motor!

2000 astro van where is the crank shaft sensor located?

front of the engine under the crankshaft pulley

What is the pulley for your timing belt directly behind the crank shaft called on a 1997 Dodge Intrepid 3.5L V6?

Timing belt crank sprocket

How do you replace the crank shaft sensor in an infiniti G35?

It is on the front of the crank shaft and under the timing belt cover. You have to remove the crank pulley and all the belts and then the lower timing cover. It is not a job for a beginner.from :

What is a crank pulley?

Crank pulley Piston connects to the crank shaft. One side of the crank shaft connects to the transmission and the other side connects to the crank pulley. It serves two main purpose. First one is it is used to time the engine (marks etched into it by manufacture) the other is to power other devices such as the alternator or power steering via a belt system (older cars used chain and gear sys). It is usually found closes to the bottom of the engine at the front, just follow the belts to the bottom.

Where is the crankshaft sensor on a 2001 Alero?

its on the front of the motor by the crank shaft pulley or it could be on the back in the same spot

Whats the name and where do you find the tool you need to remove the crank shaft pulley on a 94 Honda accord ex?

Honda Crank Pulley Tool 50mm. The part number is 646796 at There is a video that shows it in use.