0
i can answer this as i have alread done this. NOTE: these are instructions for a sunfire withOUT power windows/locks, if you have power w/l the steps are similar.
you must remove the screws along the bottom of the door panel. you must remove 2 screw in under the door "arm rest" (they're toward the front) you MUST remove the metal clip behind the window crank (those with pwr w/l don't have to worry about this step obviously) to do this: you can try to use a thin towel. placing it between the panel and the thin black disc and pulling in a teeter-totter motion. HOWEVER, the best and easiest way to do this is to get ahold of the tool made to do this. it can be picked up at most local auto stores. Or if you live near a best buy or other stores that does installations, tell them you are having trouble getting them out and ask them to remove them for you. (they have a Snap-On tool for this and it works like a CHARM!!) once the metal clip is removed pull the window crank off once you have the bolts and screws removed, you need to go along the edges of the door panel with a long screw driver or your hands and separate the panel fromm the door (there are several push-pin that hold it to the door) then lift up and out slowly. you'll have to move it around the door handle. before you try to complete take the panel off, UNHOOK the speaker wiring (and power doors/locks if you have them)
to put the panel back on, basically repeat the steps. the first thing you need to do is put the panel back on by starting at the top where the window comes out. there should be a groove that the door rests on. then line up all of the push-pins with their holes (and connect any needed wires) put the bolts back in under the arm rest, and along the bottom of the panel, then the window clip. (this may take a few attempts, but you'll get it)
What else can I help you with?
Will a door from a 1994 z24 fit a 2000 z24?
No only 1995-2004 will work Pontiac sunfire doors from 95-04 will work also but the door moulding and door panel will need to be changed
How do you install a window motor on a 1995 Pontiac Sunfire?
To install a window motor on a 1995 Pontiac Sunfire, first, remove the door panel by unscrewing all fasteners and carefully prying it off. Disconnect the electrical connector from the old window motor and remove the mounting bolts to take it out. Install the new window motor by securing it with the bolts and reconnecting the electrical connector. Finally, reattach the door panel and ensure everything is functioning properly.
How do you remove the front door panel on a 2003 Pontiac sunfire to change the speakers?
there is screws around the door panel and the right under the handle there is 2 of them then your door is off hope this helps you :)
Where is the fuse box location for a 95 Pontiac sunfire?
The fuse panel is located in the side of the dash where the driver's door closes against it
How do you repair door hinges on a 2001 Pontiac Sunfire?
Fix It.
Location of power window motor in a 1996 Pontiac sunfire?
I can't tell you precisely, but you'll see it when you pull the inside door panel off to access it.
Where is the fuse box on a 1999 Pontiac Sunfire?
Not positive on your model, but open the driver's side door and look at the end of the dashboard. There should be a little access panel.
How do you remove the door panel from a 2000 Pontiac Sunfire?
You need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.
Where is the paintcode on a 98 Pontiac Sunfire?
usually on the driver side door
Where is the fuse box on a 1995 Pontiac Grand Prix?
When you open the passenger side door ... there is a pop out panel on the side of the dash where the dash meets the door.
What is the correct tire pressure for a 2002 Pontiac sunfire?
The side of the driver's door on my 2002 Pontiac sunfire is a little hard to read, but I believe it says 30 PSI.
How do you change the window regulator on a 1998 Pontiac Sunfire Convertible?
To change the window regulator on a 1998 Pontiac Sunfire Convertible, first, remove the door panel by unscrewing the screws and gently prying it off. Disconnect the window switch harness and any other connected components. Next, remove the old regulator by unbolting it from the door and carefully taking it out, then install the new regulator by following the same steps in reverse. Finally, reattach the door panel and test the window operation.
