0
What else can I help you with?
What is the torque setting for Geo Tracker head bolts?
The torque on my 1993 is 46 ft lbs.
What are the torque specifications for Chevrolet truck brake caliper bolts?
For the Chevrolet S-10 model years from 1982 to 1993, the torque for the caliper mounting bolts is 37 ft. lbs. The torque setting for the brake hose-to-caliper bolt is 32 ft. lbs.
What are the 1993 Tercel front axle torque setting?
The hub nut is 137 ft lbs......... The two lower bolts and nuts that the strut mounts to wheel assembly is 167ft lbs......... Dont over torque that hub nut you will have problems.......................
What are the torque specs for the flywheel bolts on a 1993 jeep grand Cherokee 4.0?
105 ft
What are the torque specifications for head bolts on a 1993 Chevy Cavalier?
the longer (new bolts) are to torqued to 48lbs and the shorter ones are to be torqued to 45lbs then turn the bolts an additional 90 degrees the bolts need to be replaced with new one because they are streched when you torque them down
Where are the torque bolts on a 1993 Olds Cutlass?
Torque is not the type of bolt but a type of wrench used to tighten bolts. A torque wrench will tell you how tight a bolt is tightened like 60lb of torque or tighten to 80lb of torque so a bolt will be tight enough to stay in but not too tight that you strip the bolt.
What is the cyliner head torque setting for a 1993 Polaris 250 4x4?
18 foot pounds
What is the spark plug torque setting on a 1993 Ford Tempo?
The spark plug torque spec range is between 6 and 10 ft/lbs.
What is the torque specs for head bolts on 93 toyota pickup 22re?
Torque the head bolt on a 1993 Toyoto 22RE three times at 58 foot pounds of torque. The 22RE head bolts are not torque-to-yield (stretch), and are re-usable. Torque is 55-63 foot pounds. Thoroughly clean the bolts on a wire wheel and inspect for pitting, especially in the threads and replace as necessary. It is also recommended to re-torque them after about 1,000 miles. ChaCha!
Torque specs and sequence for head bolts for 1993 3.8 ford?
For my Mercury Cougar with Aluminum Heads it is:Torque Sequence 1993 3.8 Cougar; Looking at Engine from front of car the lower bolts are 7 3 1 5 upper bolts are 8 4 2 6. Step 1; Torque in Sequence to 37 FT./ LBS Step 2;Torque in Seq. To 45 FT./LBS. Step 3; Torque in Seq. To 52 FT,/LBS. Step4; Torque in Seq. To 59 FT./LBS. Step 5; Back off all bolts in Torque Sequence 2-3 turns. Step 6; Retorque all Bolts in Sequence 11-18 FT/LBS. Step7; Rotate Long Bolts 85-105 Degrees, Short Bolts 65-85 Degrees in Sequence. Recheck final Torque in Sequence. When replacing Head Gasket be sure to replace all torque-to-yield style Head Bolts. Hope I Have Helped -u-. "Odie" OdiebuiltMC@aol.com
What are the torque specs for a 1993 Buick lesabre intake manifold?
You did not mention if it was the intake to the cylinder head bolts (1993 buick lesabre 96 in-lbs)..... or ..... the intake upper to lower bolts ( 1993 buick 132 in -lbs) but i hope you will know wich you are looking at since there is a large difference in torqe.
When was Fiesta Marina Cruises created?
Fiesta Marina Cruises was created in 1993.
