0
How do you remove the drivers side window motor in a 1993 S10 Blazer?
Wiki User
∙ 18y ago
First, make sure it isn't a window switch. many people have bought expensive replacement motors, when the problem was only the switch in one of the doors. If one switch is bad, the other one will not work & the window will not move. If it is the motor, then is is strongly advised to buy the motor with the regulator attached to it. The doors on these trucks are a PAIN to work with. Take off the plastic door panel, unbolt the inner steel door panel, be careful & release the linkages, while tilting the steel inner panel to unhook the regulator from the window. this is NOT a fun job.
Wiki User
∙ 17y ago
Wiki User
∙ 12y agoYou will need to: disconnect battery, unscrew torx screws/ bolts around armrest, unplug power locks, windows etc. Carefully pop off plastic connectors located around door panel perimeter one at a time and be sure not to lose any.Unscrew remaing trim screws as necessary. Remove door panel. Remove vapor barrier. I wound remove the track assembly and motor as an assembly IF they are riveted together. If they are, I would replace the track and the motor by getting one at a salvage yard. The track assembly unbolts at about 3 or 4 places so have someone help you hold the window cause it will drop when you remove the last bolt. Reverse to install.
Wiki User
∙ 16y agoThere are several online references that show pictures on how to do this. I have done it. Remove Door Trim Pannel first, there are several wires to disconnect and plastic pins to pull out of the door along with a few screws. Remove the clear plastic water shield covering the door.
Use Duct Tape over the top of the door to hold the window in the up position. Unplug the motor. Drill out the rivots that hold regulator assembly to the door. Slide the regulator wheels out of the upper and lower tracks. At the bench run a sheet metal screw through the gear to the one of the regulator arms to lock the arms in position. If you don't do this when you remove the motor the springs will cause the arms to move. Drill out the small rivets holding the motor to the regulator. Use Sheetmetal screws the fasten the new motor to the regulator. Don't use the little machine screws and nuts that come with the replacement motor. At least the ones I got were junk. Remove the sheet metal screw locking the gear to the arm. Put entire assembly back into the door and fasten the regulator back to the door using the heavy duty peal rivets if you have the tool otherwise you can use 1/4-20 bolts and lock nuts. One other trick I will mention is you may want to run the new motor down a little so it is not up all the way when you try to reinstall the regulator.
Have someone help you hold the window up an extra set of hands really helps out here. Good luck.
Wiki User
∙ 9y agoRemove the weather seal from around the rear window. Remove the window retainers. Gently tap on the window from the inside. The window will fall backwards. Reverse the process to install the new window.
Wiki User
∙ 18y agoFor step by step instrustions with picts go to . http://www.a1electric.com/s10motor.htm
Wiki User
∙ 15y agoUmm...
Add your answer:
Earn +20 pts
2000 Toyota Sienna driver power window motor failure how to remove?
How do you remove and replace the motor for the drivers side power window in a 2000 Sienna
How do you repair a drivers side window motor on a 1988 Lincoln Town Car?
Remove the inside door panel of your 1988 Lincoln Town Car. Remove the wiring harness from your window motor. Remove the window motor retaining screws. Reverse the process to install a new window motor.
How do you remove voltswagen cabrio power window motor?
Buy a chilton's or haynes maintenance manual. They tell you everything. I had to replace my drivers side window motor. Not too hard.
How do you replace the window motor on a 2002 Chevy Cavalier?
Remove the inside door panel of your 2002 Chevy Cavalier. Remove the window motor wiring harness. Remove the window motor linkage. Remove the window motor retaining bolts. Reverse the process to install the new window motor.
How do you replace window motor on a 1994 Chevrolet Corsica?
Remove the inside door panel of your 1994 Chevrolet Corsica. Remove the window motor wiring harness. Remove the window motor linkage. Remove the window motor retaining bolts. Reverse the process to install the new window motor.
96 ford Windstar power window motor removal?
I need to know the best way to remove and install the new window motor for a 96 Ford Windstar drivers side. Ray
Wjy wont my75 k5 blazer rear window unroll?
It you can hear the window motor moving, then the window came unclipped. If you can't, the window motor is dead.
What does the plastic on the rear window motor of a 2001 S-10 Blazer look like?
The plastic on the rear window motor of a 2001 S-10 Blazer is black. It surrounds the majority of the motor and is easily distinguishable from the metal.
How do you install a new power window motor in a 1997 Mercury Cougar?
Remove the inside door panel of your 1997 Mercury Cougar. Remove the wiring harness from the window motor. Remove the window motor linkage. Remove the window motor retaining bolts. Reverse the process to install the new window motor.
1988 blazer tail gate power window will close with with key in tail gate but will not open window?
The 1988 Chevrolet Blazer tailgate window motor might be bad and need to be replaced. The window motor fuse might be blown and needs to be replaced.
How do you replace a power window motor on a Chevy El Camino?
You will need to remove the inside door panel of your Chevrolet El Camino. Remove the wiring harness from the window motor. Remove the window motor linkage. Remove the window motor retaining bolts. Reverse the process to install the new power window motor.
How do you change a 2002 Honda civic window lift motor?
Remove the inside door panel. Remove the wiring harness from the window motor. Remove the track linkage. Remove the window motor retaining screws. Reverse the process to install the new window motor.
