0
What else can I help you with?
How do I wire T8 multi volt lights fixtures to 220 volts?
The terminology T8 suggests to me that the fixture is a fluorescent fixture. These types of tube fixtures need a ballast to make the tubes ignite. If you are trying to operate this type of fixture on 220 volts, you will need a ballast that requires a 240 volts input voltage source.
Can you wire a 347 volt ballast to a 120 volt fixture?
Yes, but it will not work.
How many volts are 16milli - volts?
0.016 volt
Can you take a 120 volt ballast and use it in a 277 volt light?
Yes, if there is a 208 volt connection on the multi tap ballast. One side of the 208 to the common terminal and the other side of the 208 supply to the 208 volt lead. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed. Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
What difference between a kilovolt and volt?
999 Volts A Kilovolt is 1000 volts.
How do you rewire a 110 volt HID Magnetic coil ballast to use 220 volt?
Rewiring a 110 volt HID magnetic coil ballast to operate on 220 volts would require replacing the existing ballast with one designed for 220 volts. Attempting to rewire the ballast could lead to overheating, electrical failures, or even safety hazards. It is recommended to consult a professional electrician or purchase a new ballast suitable for 220 volts.
What happens if you wire 347 volts to the 120 volt tap on multi tap ballast?
Wiring 347 volts to the 120-volt tap on a multi-tap ballast can cause serious damage to the ballast and connected fixtures. The excessive voltage can lead to overheating, insulation breakdown, and potential failure of the ballast components. This may also pose a fire hazard and could damage the connected lamps or fixtures. It's crucial to always match the voltage rating of the ballast with the supply voltage to ensure safe and proper operation.
Can you wire a 120 volt ballast to a 347 volt circuit?
No, you cannot wire a 120 volt ballast to a 347 volt circuit. The ballast is designed to operate at a specific voltage, in this case 120 volts, and connecting it to a higher voltage circuit like 347 volts can damage the ballast and pose a safety hazard. It is important to match the voltage rating of the ballast to the circuit it will be connected to.
How do you wire 347 volts ballast to 110 volt feed?
You don't. A ballast with a 347 volt input is a commercial ballast. The 347 volts comes from a 600 volt three phase four wire Y system. You can change the ballast out to a 120 volt and rewire the unit but in most cases it is cheaper to buy a completely new lighting fixture.
Will a 220 volt ballast operate from a 230 volt source?
Yes, 220 volts is in the same voltage classification as 230 volts.
How do I wire T8 multi volt lights fixtures to 220 volts?
The terminology T8 suggests to me that the fixture is a fluorescent fixture. These types of tube fixtures need a ballast to make the tubes ignite. If you are trying to operate this type of fixture on 220 volts, you will need a ballast that requires a 240 volts input voltage source.
Will 120 - 277 volt electronic fluorescent ballasts work on 208 volts?
NO! a 120-277 electronic ballast requires one "hot" wire and a neutral from either a 110V or 277V supply. If you supply it with two "hot" wires from a 208 V supply, it will instantly burn up.Yes. A ballast with a specification range of 120 volt to 277 volt will work on 208 volt. These ballast use intelligent voltage sensing technology and it does not matter if the source is a hot and neutral or two (2) hots. Don't believe it? Call a ballast manufacturer instead of giving incorrect answers.
Can you run 110 volts saftely through a 277 volt ballast?
No, it is not safe to run 110 volts through a ballast rated for 277 volts. Ballasts are designed to work with specific voltage ratings to ensure safe and efficient operation. Using the ballast with the incorrect voltage could damage the ballast or create a fire hazard. It is important to use the correct voltage for the ballast to prevent any safety issues.
What is a 277 volt fluorescent fixture?
A 277 volt lighting fixture is one that is usually used in an industrial application. The reason for this is the voltage rating. A voltage potential of 277 volts is the voltage to neutral (ground) of a three phase four wire 480 volt distribution system. 480 volts / 1.73 = 277 volts. Rather than having to add a transformer to the system to provide 120 volts for lighting, manufactures produced a ballast for fluorescent fixtures that operates on the 227 volt potential.
What happens if you use a 12 volt coil with a 6 volt system?
Probably not much because 6 Volts is not enough to power a 12 Volt coil
Volts are measured in?
A volt is a volt is a volt.
Measure in volts?
A volt is a volt is a volt.
