0
Add your answer:
Earn +20 pts
How do you remove the steering lock on a 1994 Ford Probe?
# Disable airbag system. # Remove steering column covers and lower instrument panel cover # Lower steering column # Disconnect the shift interlock cable from ignition lock housing # The lock assembly is clamped to the steering column by two shear-head bolts. Drill heads off each bolt and remove the bracket. # Remove the steering lock assembly from the steering column
How do you remove the ignition lock cylinder on a 1973 Firebird?
pull steering wheel off, remove the steering lock disc, then remove the signal light switch assembly to gain access to the retaining screw that holds the lock cylinder in place,
How do you remove ignition switch from steering column on 84 Pontiac fiero?
you have to remove the steering wheel then using a lock plate removal tool depress the lock plate and removed the clip that holds it in place then remove the lock plate then remove the screws from the turn signal switch and pull it up slightly then remove the screw that hold the lock cylinder in place then remove the lock assembly
1994 mercury villager shift lock solenoid?
The shift lock solenoid is located on top of the steering column. You will need to remove the steering column covers, lower dash trim, and the heater duct. Remove the steering column bolts and lower the steering column to access the shift lock solenoid.
How do you pull an ignition for 1984 Pontiac fiero 2m4?
Remove steering wheel Remove Steering lock plate Place ignition in on position Depress lock pin now exposed. If this is not possible, drill out lock pin.
How do you remove pop a lock bar?
What is a pop a lock bar? Do you mean a club on the steering wheel?
How do you get at the turn signal in the steering wheel of a 1997 Buuick lesabre?
youll have to remove the air bag pad and horn contact pad and steering wheel. there is then underneeth a steering lock plate , yull need a steering wheel puller for(also for remoal of the steering wheel) and also to depress the spring loaded lock plate to remove the c-clip then slowlly release the pressure on the lock plate and remove it underneah will be the signal light switch assmbly.
Where is the immobilizer in an 01 Opel Astra?
the immobiliser is mounted to the steering lock, u need to remove the steering wheel and column to get to it
How do you remove the ignition switch from a 1988 Dodge Ram 50?
Ignition switch and lock cylinder removal 1988 Dodge Ram 50.Disconnect the negative battery cable from the battery.Remove the steering column cover to gain access to the ignition switch/lock cylinder.Using wire cutters, remove the cable band.Remove the bolts that hold the ignition switch/lock cylinder to the steering column.Unbolt and remove the key reminder switch and remove the switch lock cylinder from the steering column.
How do you replace steering lock laguna 2?
take out your cluster clock there's 2 nuts under it for the steering colum , once u have the steering colum loose u need to pull it forward to gain access to the dreaded allen key it's on the radio side of the steering lock and it opens the opposite way than normal , btw the steering lock must be open to remove it from the colum if its stuck locked there is a way to unlock it remove the steering lock cover (grey plastic cover) and unclip the actulator
How do you replace the ignition switch on a '94 Saturn station wagon?
switch removal1. disconnect negative battery cable2. remove the steering wheel3. unplug the wires from the switch, remove the bolts and lift switch off steering column ignition lock cylinder removal1. disconnect negative battery cable2. remove the steering wheel3. remove the knee bolster and steering column cover screws4. separate the steering column covers and pull the upper cover up for access to the lock release tab5. with the key in the acc position, depress the release tab, then pull the lock cylinder straight out and remove it from the steering column.
How do you replace the ignition lock cylinder on your 1993 Ford Festiva?
remove the two screws holding face plate in center of steering wheel and remove plate. next remove large nut in center. Using a steering wheel puller remove steering wheel. next there is a pin next tothe lock cylinder. that will have to be driven inwith a hammer and a punch. lock cylinder should be able to be pulled out. installation is the reverse of removal.
