0
What else can I help you with?
Can you have a square hole?
off course you can
How large of a hole does a bat need to get in a house or attic?
A hole the size of a quarter is plenty big enough to allow entrance to a bat.
What is 12 inch square hole in basement floor for and it has a 6 inch capped pipe in it?
12x12 square hole in basement floor what is it for
What does the word hollow mean?
The word "hollow" has the following definitions:having a hole or empty space inside.without significance; insignificant.to form by making a hole.
How do you figure out how much rock you need to fill a hole?
how much 1" rock will I need to fill in a hole 20' long, 2' wide' and about 2' deep
How big a hole is needed for a shower valve?
Typically a hole for a single handle shower valve can be easily created by a good 3 5/8" hole saw. If u are installing a 2 or 3 handle valve the hole is 1 1/8inch hole saw. Take care in using the hole saw. Please read all manufacturer directions before u install this valve.
What is the process for accessing and replacing the shower valve located behind the wall?
Accessing and replacing a shower valve located behind the wall involves cutting a hole in the wall to reach the valve, shutting off the water supply, removing the old valve, installing a new valve, and then patching and repairing the wall. It is recommended to consult a professional plumber for this task to ensure it is done correctly and safely.
How can I remove a Delta shower handle that does not have any visible screws?
To remove a Delta shower handle without visible screws, look for a small hole or cap on the handle. Use a flathead screwdriver or Allen wrench to pry off the cap and reveal the screw underneath. Unscrew it to detach the handle from the valve.
How can I remove a Delta shower handle that does not have a set screw?
To remove a Delta shower handle without a set screw, look for a small hole or slot on the handle. Insert a flathead screwdriver or an Allen wrench into the hole and twist counterclockwise to loosen and remove the handle. If there is no hole or slot, try gently prying the handle off with a flathead screwdriver or a handle puller tool. Be careful not to damage the handle or the surrounding area.
How do you change PVC VALVE in 2003 Dakota?
the pcv valve is located on the oil filler neck, remove the hose and rotate to remove! you should clean the hole before installing a new one!
How do you replace a shower valve?
i would advise that you get some Teflon tape at the hardware store this will help seal the screws so water doesn't leak out when you turn it on. 1. first you need to unscrew the shower head off.2. then wrap the screw threads in the Teflon tape(this part can be a little tricky and if you know anything about telfon you can quess why).3. then just srcew they new shower head on but make sure you do it nice and tight. that's for your standard shower head but if you have one of those hose shower heads there some extra steps and a lot more teflon. 1. do steps 1-2.2. then but on the base that holds the shower head. 3. then wrap teflon on the part of the hose that goes in the base.4. put hose in base.5. attach hose to head then put head in base holder. That how you but on a new shower head.
What are the best practices for installing a shower drain insert?
To install a shower drain insert, follow these best practices: Ensure the drain hole is clean and level. Apply waterproof sealant around the edges of the drain insert. Insert the drain and secure it in place. Test for leaks before finishing installation.
Where is the PCV valve in a 1991 2.5 Jeep wrangler?
Its on the front of the valve cover the first hole behind the oil fill hole
What is the standard hole size required for installing a door knob?
The standard hole size required for installing a door knob is typically 2 1/8 inches in diameter.
What size hole saw should I use for installing a door knob?
For installing a door knob, you should use a hole saw that is 2-1/8 inches in size.
How do you change a triple valve shower control to a single lever control?
The connections on the faucet are pretty much the same for the type of piping you have. They should swap out fairly easily. There is a trim plate available that covers the old holes and gives you the single hole in the center.
How do you figure the output of your shower head?
By measuring each hole in the shower head and getting the pressure and then mathematically it can be figured out
