a war of attrition means a slow-moving war which takes place in the trenches. it is trench warfare. neither side leaves their trench and enemies are slowly picked off. the conditions in the trenches were horrible and neither side knew how to deal with trench war fare, therefore the was goes VERY slow.
Trench warfare limited territorial gains on either side.
A dugout was a trench that was dug and roofed over as a shelter for troops.
After initial advances by Germany on the western front, the war stalled as trench warfare created powerful defensive positions on each side,
To leave the trenches and attack the enemy. A very British tactic you climb out of your trench and walk towards the enemy while being shot at with machine guns. The Somme is one such battle where the tactic was employed resulting in the loss of 58,000 British troops in one day (still a record)
A trench was set up in a zigzag shape to make it a less target for the opposite side to target. It consisted of sandbags, barbed wire, fire steps and unsanitary places to do your business.
The front wall, the side facing the enemy, is called a parapet.The rear wall is called a parados.
That is the pump for the rear air suspension.
When sandbags are piled up in long lengths, they fit together so tightly that flood water on the other side cannot run through. Water does soak through, but the amount is relatively small. You could say that sandbags are placed to form a dam against the flood waters.
WWI used trench warfare. This is where each side dug miles and miles of trenches (in France here). Then each side would try to gain an advantage. charges of a section of the army, artillery, snipers, machine gunners, later bombs from aircraft barbed wire (takes time to get through, get caught on, blown to bits by a machine gun while trying to free yourself) protected the trenches as well as sandbags (absorbed bullets, easy to make walls with) for more look it up on wikipedia enjoy :)
The side slits stand for a deep ocean trench.
The one that lights the outside edge, a marker light to be seen from the side
Sandbags are amazingly helpful when it comes to protecting small areas from floods. Sandbags are very easy to create. All you need is sand, polyethylene sheeting, a shovel, a bag for the sand, and wheelbarrows. These are easily available in any hardware supplies store. That’s it! You are now ready to make a sandbag of your own in four easy steps. With the help of another person to hold the bag, fill it with sand. Make sure the bag is only half full and ideally should weigh less than 40lbs. Once the sand is filled, the empty part of the bag should be folded and placed that side down. This will prevent water from seeping in. A single sandbag that leaks can ruin the whole pile. A trench measuring 5 inches deep and 20 inches wide has to be dug around the area that needs to be protected. The polyethylene sheeting has to be laid on the trench and be secured by sandbags that are placed in such a way that they directly face the flowing water. Create new rows only after completing a row as leaving space is not advisable. The best way to build a stack of sandbags is to build it similar to how brick walls are created. This adds more protection to the sandbag wall being built. Normally a three layer stack of sandbags are considered to be sturdy enough and hence sticking to a three layer stack is advisable. That’s all! The sandbags are now ready to protect against flooding. These sandbags can be preserved to use for the following rainy seasons. Enough care has to be taken to ensure that the bags are prevented from repeatedly getting wet. This will give them a longer life span. Also, when not being used the bag has to be emptied and kept aside for use next year. Though sandbags are wonderful at protecting, it must be noted that they are best suited for certain jobs. A two person team will have difficulty protecting a large area. Soil can be a good substitute when sand is not available, and filling the bags with cement will create a more permanent barrier than sandbags.
Trench raiding began in World War I and was performed by both sides. It is when one side makes a small surprise attack on the other side during the night.
the characteristics of the trench warfare were that each so called "team" had faught the war from a trench that they had dug at the battle field. this had made it harder to kill people on the opposing side.
When a piece of the ocean floor cracks, one side of the crack will sink beneath the other side. As it sinks, it pulls the rest of its plate with it. The sinking sea floor grinds against the other side of the crack and tears parts off. The result is a long, deep trench. This process is how the Mariana Trench formed.
It is on the driver side rear of the engine.It is on the driver side rear of the engine.