answersLogoWhite

0


Best Answer

If its a new Liberty just call the Dealer or any Dodge/Chrysler Dealer for the location. On the 2002 Liberty it is in the right rear corner. You remove the plastic covering and there is the connector there where you can connect in an adapter. There is also a rubber plug in the right rear corner intended to allow you to feed the wire out without drilling a hole. You then reseal the rubber grommet with silicone sealant.

User Avatar

Wiki User

โˆ™ 2006-02-09 18:06:39
This answer is:
User Avatar
Study guides

Add your answer:

Earn +20 pts
Q: Where is the connection for the taillight wiring to connect a trailer wiring harness in a Jeep Liberty?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Music & Radio

Do you get a small amplifier that you can install in a car door and connect on the speaker line that comes from the radio?

No. You buy a waring harness and connect it to the car wiring and the amp to the speakers there behind the radio.


On the factory radio wire harness of a 2002 Oldsmobile Alero what color do you connect to the remote wire of your amplifier?

If it is a RDS system, then you will need to connect the blue wire to the remote wire on the amplifier.


Where do you connect the red power wire for aftermarket radio in new gm?

That depends. There should be two red power wires on the back of an aftermarket deck. One will be 'constant' power, the other will be 'switched' power. The 'constant' one always has power, so that radio stations and other settings aren't erased when the vehicle is turned off. I'm assuming you're not using an adapter harness to connect the aftermarket deck directly to the GM radio harness.(always the preferable option) Most of the time(when not using an adapter harness) I will locate a pre-existing wire in the dash that is 'constant', and tap into that for the 'constant'. The 'switched' power can be connected to the factory radio's 'switched' power source. You'll have to figure out which wire that is in the GM harness and connect to that, or (not so ideally) cut that wire and connect it to the deck.


Where to find wiring diagram of radio harness for 2000 Honda civic?

This site will show you the wiring diagram of a radio harness for just about any vehicle. Hope it helps http://www.the12volt.com/ or do it the old fashion like i did if the radio diagram says the blue wires on the radio are for the left front grab the wires from the harness coming from the car and grab the two from the harness and connect them together and if the back right speaker comes on , disconnect them and grab the wires from the radio that says back right and connect those two. repeat this until the others three are sounding in the right order until done


How easy would it be to replace wiring harness for the heater resistor on a 2004 silverado?

Its very easy, go to your local GM parts counter and order a pigtail for the blower motor resistor harness, all you need to do is cut and connect the appropriate wires together and youll be all set.

Related questions

Where is the connection for the taillight wiring to connect a trailer wiring harness in a 2003 Jeep Liberty Sport?

It is the round connector, with a cover over it, about 6 inches left of and about at the same level as the hitch receiver.


Where is the brake light wiring harness for 1989 Chrysler Lebaron?

It plugs into the taillight.


What color is the backup light wire in a 2003 Passat taillight harness?

i dnt no i dnt no


What does the pink wire in the wiring harness connect too?

the harness


How do you change a taillight bulb in 2006 Mustang?

* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops


How do I Replace tail light 2006 mustang?

Taillight bulb replacment/Taillight housing replacement * Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops


How do you replace a taillight bulb on a 2006 ford mustang?

* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops


How do you disconnect taillight wires 2002 silverado?

remove the 2 bolts/screws attaching the lens to the bed, after that unplug the harness and your done


How and where do you connect the turn and taillight wires for a trailer lighting connector on a Lexus ES-300?

It sounds as if you either don't have a wiring harness attached to your vehicle, or else you will need to get an adapter. All the plugs and sockets are different, depending on who made it, and how many connectors each one has.


Bundles of wires that connect computer parts?

Harness. Cables.


How do you change a tail light on a 2006 mustang?

* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops


How do you change the tail lights on a 2007 mustang?

* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops

People also asked