0
What else can I help you with?
Star-star connection of transformer?
Star Star TransformerStar Star Transformer is formed in a 3 phase transformer by connecting one terminal of each phase of individual side, together. The common terminal is indicated by suffix 1 in the figure below. If terminal with suffix 1 in both primary and secondary are used as common terminal, voltages of primary and secondary are in same phase. That is why this connection is called zero degree connection or 0o - connection.If the terminals with suffix 1 is connected together in HV side as common point and the terminals with suffix 2 in LV side are connected together as common point, the voltages in primary and secondary will be in opposite phase. Hence, Star Star Transformer connection is called 180o - Connection, of three phase transformer.Vikram Meena
Does the formula used to calculate the turns ratio uses the phase voltages and phase current?
For a transformer, the turns ratio always applies between its primary and secondary windings. So the turns ratio for a three-phase transformer is the ratio of primary to secondary phase voltages, not between line voltages.
Is the turns ratio of transformer the same as the ratio of voltages across the transformerwhy or why not?
In general the turns ratio is equal to the ratio of voltages. A few turns might be added to the secondary to provide extra voltage to offset the voltage drop caused by the resistance of the secondary when the transformer is supplying a load.Another AnswerFor an 'ideal' transformer, the answer is yes, and the reason is based on the e.m.f. equations for a transformer which, for the primary winding is: Vp = 4.44 Np f x flux ...and, for the secondary winding is: VS = 4.44 NS f x fluxSince the frequency (f) and flux is common to both windings, dividing one equation by the other will result it:VP/VS = NP/NSSo, as you can see, the voltage ratio and the turns ration are the same.
If a 120v transformer has 200 turns the secondary winding has 20 turns what is the secondary winding voltage?
The ratio of AC voltages is the same as the ratio of winding-turns in the transformer. Vp / Vs = Np / Ns (10 volts AC) / Vs = 200 / 20 = 10 Vs = (10 volts AC) / 10 = 1 volt AC.
Can you use a 1000watts transformer with a 700 watts appliance?
Yes, you can use a 1000 watts transformer with a 700 watts appliance. The transformer's capacity should be equal to or greater than the appliance's wattage to prevent overloading or damage. In this case, the 1000 watts transformer has enough capacity to safely power the 700 watts appliance.
Star-star connection of transformer?
Star Star TransformerStar Star Transformer is formed in a 3 phase transformer by connecting one terminal of each phase of individual side, together. The common terminal is indicated by suffix 1 in the figure below. If terminal with suffix 1 in both primary and secondary are used as common terminal, voltages of primary and secondary are in same phase. That is why this connection is called zero degree connection or 0o - connection.If the terminals with suffix 1 is connected together in HV side as common point and the terminals with suffix 2 in LV side are connected together as common point, the voltages in primary and secondary will be in opposite phase. Hence, Star Star Transformer connection is called 180o - Connection, of three phase transformer.Vikram Meena
How are lower voltages combined into higher voltages for transmission?
Low voltages are not 'combined into higher voltages' for transmission! The lower voltage (e.g. the voltage generated at a power station) is applied to the primary winding of a large power transformer, and the required higher transmission voltage then appears across the transformer's secondary winding. The magnitude of the secondary voltage is determined by the turns ratio of the transformer's windings.
What happen if the number of loops in the primary and secondary coils in a transformer are the same?
If the number of turns in the primary is the same as the secondary, this would be an isolation transformer. Primary and secondary voltages should match (minus the inherent transformer losses), as should the current.
What is phase shift in three phase transformer?
The phase shift in three-phase transformer from winding of Transformer and determine by vectorgroup of transformer such as YNd1 High voltage connect to wye Low Voltage connect to delta so L.V. lag H.V 30 degree.Answer'Phase shift' or, more accurately, 'angular displacement', is the angle between the secondary line voltages and primary line voltages of a three-phase transformer.
Does the formula used to calculate the turns ratio uses the phase voltages and phase current?
For a transformer, the turns ratio always applies between its primary and secondary windings. So the turns ratio for a three-phase transformer is the ratio of primary to secondary phase voltages, not between line voltages.
Is 3 phase star transformer has more winding than delta?
The # of windings in a transformer are based on the primary and secondary voltages the transformer is rated for not the way the windings are connected.
What is the vector diagram of ynd11 transformer?
In the vector group representation for this transformer, the letter 'y' represents a wye- or star-connection, and the letter 'd' represents a delta- or mesh-connection (I have no idea what 'n' stands for -anyone?). An upper-case letter indicates the higher voltage, while a lower-case letter represents the lower voltage. The sequence of the letters indicates the primary and the secondary windings. So the transformer in question is a wye-delta connection (presumably the 'y' should have been capitalised, meaning that this is a step-down transformer: i.e. Yd11).The number appearing after the letter group (in this case '11') is a multiplier of 30o and indicates the transformer connection's angular displacement (or phase displacement). In this case, the angular displacement is 11 x 30o = 330o.As angular displacement is defined as 'the angle by which the secondary line voltages lag the primary line voltages', this means the secondary line voltages of this particular transformer lags its corresponding primary line voltages by 330o.So, to draw the phasor (not 'vector') diagram for this particular transformer, you would start by drawing the phase voltages (VAN, VBN, and VCN) of the primary wye connection (using VAN as the phasor of reference), from which you would then construct the corresponding line voltages (VAB, VBC, and VCA). To finish the diagram, you will then draw the secondary delta phasor diagram, starting with Vab lagging VAB by 330o (or, if you prefer, leading by 30o), then drawing Vbc and Vca displaced by 120o.
What is approximate turns ratio of the centre-tapped transformer used?
It depends on the voltage ratio of the transformer. If you know the primary and secondary voltages, then you can work it out for yourself.
What is the amount of primary current needed to supply the first secondary winding?
To determine the amount of primary current needed to supply the first secondary winding, you would typically use the transformer equation, which relates primary and secondary voltages and currents. The equation is ( V_p / V_s = I_s / I_p ), where ( V_p ) and ( V_s ) are the primary and secondary voltages, and ( I_p ) and ( I_s ) are the primary and secondary currents, respectively. By rearranging this equation, you can solve for the primary current ( I_p ) needed to supply the secondary winding based on the known values of the transformer’s voltages and the secondary current. Additionally, efficiency and losses in the transformer should be considered when calculating the actual primary current required.
Is there a basic difference between a three phase power transformer and a three phase distribution transformer?
The basic difference is the secondary voltages. On a distribution transformer the secondary voltage is very high. This is to overcome line loss for transmission of electricity over long distances. A three phase power transformer is used at the consumers three phase services end to manipulate voltages that consumers need to operate their equipment. The transformer that feeds your house is considered to be a single phase power transformer.
What are taps for in a transformer?
The ratio of windings between a primary and secondary in a transformer govern the output voltage. Multiple taps are connections to various points in the coil effectively changing the winding ratios to get multiple voltages from the same transformer. Taps can be on the primary, secondary or both to provide a more versatile transformer.
How do you calculate current flow transformer when 240 Vrms is supply?
The secondary current of a transformer is determined by the load and the secondary voltage applied to that load, and this, in turn, will determine the primary current by the inverse of the turns ratio. However, if you are asking about a transformer's rated secondary and primary currents, then you need to divide the transformer's apparent power rating (expressed in volt amperes) by the rated secondary and primary voltages respectively.
