0
Chevy Impala
Launched in 1958, Chevy Impala is a full-size vehicle built by General Motor’s Chevrolet division. It is Chevrolet’s most expensive vehicle and US best selling automobile through 1965. It is distinguished by its triple symmetrical taillights.
4,997 Questions
Just check your overflow container after a few days, if there is any air in the system it should work it's way out and just bubble in the overflow tank. If you see the tank level drop and you don't have any leaks, then there was some air. It is not a major concern.
Where is the thermostat located and how do you replace it on a 2005 Chevy Impala 3.4L V6?
Your thermostat is located inside the thermostat housing at the end of the upper radiator hose, on the back of the engine. Just find your upper radiator hose and follow it to the engine. It's hooked to the thermostat housing. easy... now comes the fun...
To replace your thermostat, you have to remove the air intake duct (which mean unplug all your sensors on it, MAF etc). That should give you better access to the housing.
You still have the throttle body right above the housing, and you may have to remove it too for better access and that sucks...(it involves disconnecting some coolant bypass lines...make sure you drain your radiator before you do so)
You pretty much have to take off the throttle body to access the thermostat housing. A great help would be to pick up a new gasket to replace the one between the throtle body and engine BEFORE you find out you have damaged the old gasket. Also, some carb cleaner helps take the deposits out of the throttle body.
Once you have that done remove the thermostat housing (after you unplug the coolant temperature sensor) and have some towels and a bucket ready as coolant will be coming out of it.
Remove the old thermostat, remove the old gasket if necessary, and put the new thermostat with the new gasket in there (with the spring pointing toward the engine). Put some RTV sealant on the housing bolt it back on there, and put the throttle body back as well as the air duct and all the sensors. Refill your radiator, turn your engine on and check for leaks.
hope this helps
Where is the knock sensor located on a 4.0l 32 valve doc 97 aurora engine please help?
1996 Olds Aurora knock sensor is located under the intake manifold requiring removal of the intake manifold. Once the manifold is removed it is easy
Your Chevy impala floor mats are wet you have 2002?
Your heater core could be leaking, but that would smell like antifreeze. You could have had a windshield replaced by a moron, or you could have had body panels replaced by the same moron. Unfortunately you need to stick your nose in there and see if it smells like antifreeze, coz that's bad news Phil
Where can I find a climate control wiring diagram for a 2006 Chevy Impala?
When fixing problems in a car, a diagram will help make sure the changes are made correctly. The wiring diagram for this car's climate control is found in its maintenance and repair manual.
How do you remove the dash on a 2007 Chevy impala to install a new radio?
The dash does not need to come off to install a new radio. The area where the radio is installed has its own panel that can be easily removed. Grab a flat-head screwdriver and pop the cover off (there are 4 pins that grab the panel to the dashboard body). Don't forget to unplug the plug that controls the passenger air bag light before completely removing it.
Where is the low input speed sensor circuit located at on a 2002 Chevy Impala?
Under the side trany pan on the upper left corner,About a six hour job,so make sure that's the prob. before attemting .
Where is the rack and pinion located on a car?
if one bottoms out the car i.e. scrapes the bottom of the card roughly-Can one break/crack the rack and pinion?
How many horsepower does the engine in the 2003 Chevrolet Impala have?
The 2003 Chevrolet Impala's engine produces 180 hp @ 5200 rpm.
Where is and how do you replace a 1994 Chevrolet Impala thermostat?
Drain the radiator into a container. Remove the upper radiator hose at the engine end. remove the 2 bolts in the thermostat housing and remove the housing. Remove the thermostat and clean both surfaces. Install the new thermostat and seal and then install the housing and bolts. Reinstall the upper radiator hose and refill the radiator.jd
How do you install a heater core on a 1968 Chevy impala?
Bolt the heater core into place, with the four retaining bolts. Connect the water supply hoses. You might need to bleed one of the hoses to get the water flowing through the heater core.
Car speakers adaptors for my 2000 impala?
the actual adaptors themselves are not really needed, all you really need is to splice the wires and connect the positive and negative to the correct slots on the speaker you wish to hook up.
What is the code to unlock radio for 2002 impala?
If Theftlock has been activated, you have no other choice than go to the stealership or maybe the local car radio shop to have your radio unlocked. Good luck...
Can you install subwoofers to a 2000 impala stock stereo?
Yup! As a matter of fact I'm doing it right now. However, you can only do it a couple ways. You must buy and amp that has 2 inputs. One of which should be called line level. This way you can splice a wire into your current speaker wires (using the back speakers is the best) that will then go to the amp and give it the signal. Otherwise if you don't have an amp with line level input you can buy a line level input converter that you will also splice into the speaker wiring but this little device will put out a signal level input (RCA). However, when working with this kind of a car, it is a PAIN to find a place to feed your wire through the firewall. So my question is if you could just splice into the power wire to the factory amp in the back? But yea, all in all, you can do it!
When to change Timing belt on 2003 impala?
You should change the timing belt on a 2003 when it wears out or breaks. Changing the belt beforehand is not needed.
Pimp your ride MTV How do we submit video to have a ride pimped?
my name is david i am a 24 year old from the ceral city just trying to make it and provide for my wife and my daughter.Right now times are getting really hard just lost my job due to the econemy i would at a seating company and we made seats for gm for and Chrysler and now the let go about half are staff money is very hard and not seem to get better.I have been doing od jobs my self working on cars and mowing lawns trying to make money along with my unemployment.Recently on February 5 2009 my daughter Addysen was born ,born with some problems she got cought in the birth connal coming out and it messed her whole right side up, and we have been taking her to lots of theraphy and dr appointments she has made a great improvement gas is getting to be alot and the Drs are about 60 miles each way but i take her she puts a smile on everyones face shes all i got right now and i love her dearly.I have a nice original 1960 impala ive had about 6 months its a sweet car if could ever be redone this thing needs help ive been watching the show since day one i love yall style so would you please pimp my ride you guys would love this thing.
What is the spark plug wire sequence for a Chevy V8?
18436572 #1 is on the d side front then 3,5,7 moving to the rear starting in the other side from the front its 2,4,6,8 looking at the dist. the #1 plug wire is the 2ed turning clockwise from the hot and tach hookup in the side of the cap
Where is the oil pressure sending unit for Chevy 5.3L V8?
Standing in the front of the engine, It will be on the top back right side
of the engine block. Just behind the intake manifold.
