0
Crankshaft Sensors
In an internal combustion engine, a crankshaft sensor is a component used to monitor the rotational speed and position of the crankshaft. The information provided by the sensor is used by the engine control unit to manipulate ignition system timing.
2,765 Questions
Is a ford 4.9 liter 6 cylinder engine free running when the cam gear breaks?
Yes, Mine broke and the engine runs just fine now, after new gears of course.
Not enough information, some engines are internally balanced, so you can swap balancers, some engines are externally balanced which means the balancer is matched to the engine so a new balancer will have to be taken to the engine shop and made the same as the old one. When you balance a wheel the goal is zero. an engine balancer might be intentionally out of balance to counteract an imbalance inside the engine.
Where is the crankshaft sensor on seat ibiza 1998?
behind the starter motor at the back of the engine gearbox side
Check battery voltage--With engine running it should be 13.8-14.2
What does a crank shaft sensor do?
When crankshaft is turning, the sensor will provide a signal to the PCM. The PCM will then allow the engine to start by providing spark and fuel.
How do you fix wet crank shaft sensor?
You can try drying it with a hair blow dryer. If that does not work then heat your oven to 150 degrees and leave it in there overnight. If that does not work you will need to replace it.
How do you replace camshaft position sensor in 1998 Jeep Cherokee Sport?
Assuming you are asking about a 4.0L engine... Remove the distributor cap. Remove the rotor. Unplug the camshaft positioning sensor from the harness. Lift carefully where the cable feeds through the distributor to the CMP and remove. Put replacement CMP in the same place and connect it to the harness. Replace the rotor and distributor cap. Courtesy of xjtalk.com
Check the MAP sensor.
What is the difference between a cam sensor and a coil sensor?
cam sensor senses position of cam .coil sensor operates coil
both 2 entirely different parts of engine
1. Make sure you are getting fuel to the carb... 2. If you are getting fuel and spark to you spark plugs and the plugs are wet, You more than likely have a timing problem.
How do you change 99 durango 5.2 crankshaft position sensor?
i feel bad for you man, its located in between the back of the engine and the tranny in a small cut out on the top passenger side, two bolts 1/2inch if i recal from yesterday haha, but its 2 bolts, pop old out, new in, bolt it up and should be fine
Ignition module then computer.
Where is the crank position senor on 97 Mazda b2300?
It is mounted on the front of the block at the crankshaft. It is bolted on the driver's side of the engine.
How does the crank sensor work what does it read i put new sensor on and still wont start?
The sensor works by generating pulses that are sent to the PCM. The PCM will use this information to notify where the crankshaft is to determine the injector sequence and ignition timing. When you installed the new CKP, did you happen to notice if a peice of paper was on the end that went into the bell housing? The paper is cut off by the crankshaft to give the proper distance and will not work correctly without it. If you didn't have a peice of paper on it you can either go to the dealer and get the paper or you can use a cereal box and cut the small peice and glue it on.
If your crank sensor goes out how do you know which one to change?
There is only one crank sensor fitted, you may also have a cam sensor. the crank sensor is located either around the bellhousing or around the front crank pulley. It either has 2 or 3 wires. It picks the signal off the revolving crank so look for a sensor in the block near flywheel.
Why won't car start after putting in new cam shaft position sensor?
Always go back to the basics, spark, fuel and compression. If you have all three, it will run. After putting in a cam position sensor you might want to verify that it's all set up properly and everything is connected. Often it's just something little that was missed, such as putting something in backward or not having the proper clearance set-up. What does the computer diagnostic code say? That will give you more information than can be provided like this.
What are Symptoms of a bad cam sensor on 94 grand Cherokee?
There are a few symptoms when a car has a bad cam sensor. A few of these are sputtering, poor acceleration, and the engine stalling.
When you try to restart it, does it turn over but not start? If you press the gas pedal to the floor and try to start it, what happens? Does it act like it's flooded? I've seen bad spark plugs/wires/cap/rotor cause this problem, but it could also be many other things.
Camshaft sensor? Not if you have a distributor. Losing spark on acceleration is easy though. On acceleration, you increase pressure in the cylinders and thus increase the resistance across the plug gap. This, in addition to the resistance is too much resistance for the maximum output voltage produced by the coil, so you've got the following possibilities:
1- worn plugs
2- old plug wires
3- weak ignition coil
4- but less likely, eroded distributor cap and rotor
All of these parts will be replaced during a proper tune-up, so just do a tune-up and you'll be OK.
Can the crank position sensor be bad even though it checks out good with an OHM meter?
Yes, but not usually. If the computer is telling you that you have a bad crank position sensor, it could also be a connector or damaged wire. Don't be too literal.
What is the top speed of a stock 93 eagle talon awd?
220 on a straight stretch, over 240 down hill with good tires. you'll want Z quality if you go any faster than about 240
Where is the crank control module located in a 97 jeep grand Cherokee?
If it is a 6 Cly. the most likely location is at about 11:00 on the bell housing looking forward.
Very hard to get to and drooped bolts may end up in your transmission bell housing. Magnetic sockets and small hands advised.
