0
Crankshaft Sensors
In an internal combustion engine, a crankshaft sensor is a component used to monitor the rotational speed and position of the crankshaft. The information provided by the sensor is used by the engine control unit to manipulate ignition system timing.
2,765 Questions
Where is the crankshaft position sensor on a 99 olds intrigue 35 l v6 engine?
Step 1 : The Crankshaft Position Is located above the starer...
Step 2 : You have to remove the start which has 2 bolts...
Step 3 : Once you remove the starter remove the "Positive Cable" held on by a "10mm" bolt if I'm correct...
Step 4 : Once you have completely removed the starter remove the A/T brace I think it's 2 or 3 "10mm" bolts holding that on...
Step 5 : Once A/T is removed the Crankshaft Position Sensor should be visible...To easily identify there is a connector hanging out of it...It is located in the center of the block rite below cylinder 2, 4, and 6's exhaust manifold....
Step 6 : There is only 1 bolt keeping the sensor from coming out I believe it is either a "10mm" or "11mm"...once the bolt is out there is nothing keeping the Crankshaft position sensor from coming out except to O-ring...You can use a tire iron which I used but be VERY CAREFUL...Because the actually part that makes the sensor work could break off then you will need to drop the oil pan and push it through....
Hopefully This Helps...
Where is crankshaft position sensor on a 1999 Chevy Tahoe 4 wd?
If you slide up under the front bumber and look up at the bottom pulley on the front of the engine. You will see it bolted into the left side of the timing chain cover. Behind the harmonic balancer.
How do you replace crankshaft sensor on 2001 s10 blazer?
Locate the crank sensor behind the vibration damper (crankshaft pulley). Unplug the wire harness connected to it. Remove the small bolt holding the sensor in place. Remove the sensor.
Where is the camshaft sensor located on a 1997 Ford Ranger?
its mounted on the oil pump assembly behind the inner timing belt cover. that's on a 2.3L engine
Why won't the truck turn over after replacing with a new crank sensor?
your crank sensor has absolutly nothing to do with the ability of the engine turning over. I would look at the wiring to the starter.
Where is the crankshaft position sensor on a Honda?
Depending on the year it could be in the distributor or by the crank's pulley.
On 93-98 Honda passports with the 3.2l engine the crankshaft position sensor in located on the passenger side of the engine near the engine mount. 93-95s did not have the camshaft sensor though. that was added in 96 and is located on the d/s valve cover in the outside upper corner
Where is the crankshaft position sensor located on a 1997 Chevrolet K1500?
It is behind the harmonic balancer on the left front side of the timing cover.
It will have 1 bolt that holds it in.
How do you locate the crankshaft sensor on a 1998 kia sportage?
I have a 2001 Sportage and the crankshaft position sensor is located right where the engine and trans meet. I can not get to it from above as it is directy behind the dipstick by the firewall near the middle of the car. You will have to get to it from under the car. I could barely get my hand in that small space. There is one bolt holding mine on... but I can't figure out how to get the bolt off yet. Stick your hand up near the dipstick and the mounting bracket for the exhaust pipe. Unplug the one end and get that small bolt off and you're in business.
What is a crankshaft flying web?
In V6 engines using a 90 degree vee engine block (as used for V8 engine blocks naturally balanced in that arrangement, used for the V6 to save pruduction costs) the crankpin journals have to be splayed by 30 degrees to maintain an even firing order, and because the crankshaft only has 3 instead of 6 crankpin journals (which is even and balanced but not used in this case for the same production reasons as above). A crankshaft flying web is the thin webing that joins the split pins together, and of which is said to make these crankshafts considerably weaker than a 6 pin crank. This method is also used for the VW range of "W" 4, 6, 8, and 12 cylinder engines for similar reasons as highlighted above but involves a much more indepth explanation.
What if your car runs fine but the computer says you have no crank shaft signal?
The crank shaft sensor may have died and the engine controller is using other sensors to keep the engine operational in "limp" mode.
Where is a crankshaft sensor on 88 celebrity?
The location of the crankshaft position sensor depends on which engine the car has.
If it is the 2.5L 4 cylinder engine the crankshaft position sensor is behind the ignition module.
If it is the 2.8L V6 engine the crankshaft position sensor is on the side of the engine nearest the firewall and just above the pan rail in about the center of the block.
Where is the crank shaft position sensor located in a 98 Cadillac catera?
http://www.cadillacforums.com/forums/cadillac-catera-cimarron-forum/67854-98-catera-crankshaft-position-sensor-replacement.html
What is wrong if a 1996 Chrysler Sebring computer reads 'cam position sensor no signal'?
There is a problem with the cam sensor or the wiring to it.
Is there a Cam shaft position sensor in a 1999 Saturn sl?
No. And you're probably asking because you're getting a "Service Engine" code relative to the cam pos sensor, P0340 or P0341. These codes, on these cars, usually mean you need to replace the spark plugs and/or wires, or clean up all the electrical connections (including grounds) related to the ignition system.
The fix is usually very cheap. Unfortunately, many auto parts stores don't understand this, and will, confused that they can't find a listing for a cam pos sensor, will go for something that only sounds similar by name, the crankshaft position sensor. In this case, that's a total waste of money, and does NOTHING for the P0340 or P0341 codes.
Where is the camshaft position sensor located on a 1996 Honda Accord?
position sensor on a 96 accord ex located
Where is crankshaft position sensor located on a Chrysler 2.5L v6?
It is on the top rear of the transmission bell housing.
Where is the crank sensor for a 2005 Nissan Altima?
The crank sensor is on the right side of the engine if you are facing the car. It is on the side, it has a connecting wire and a 10mm bolt. To remove take the battery cable off first, then disconnect the wire and remove the bolt. The new sensor is not going to look like the old one but it will be okay. Also when you put the new one in the cable is going to plug in opposite of how you took it off that will okay as well. Before installing the new one take some clean oil and wipe it around the new sensor, replace the new sensor, replace bolt, & wire and you are in business. Whole process takes only 15 minutes.
How much does a camshaft position sensor cost on a Generation 3 Ford Taurus Mercury Sable?
The sensor itself is approximately $30 from any autoparts retail outlet. Typically however You will need to replace the whole syncronizer assembly if you are having the chirping issue. The whole assembly typically costs around $180. Stay away from the Dorman Part. It WILL Fail. A1 Cardone is known for being a direct Motorcraft Refurbished unit.
Where is the crankshaft position sensor on a 98 Hyundai elantra?
The crankshaft position sensor is located on the front side of the engine block near the flywheel/driveplate
Where is the location of crank shaft sensor on 91 Pontiac grand am 2.3?
I am serious on this answer, go to Autozone.com, sign up to become a member for the vehicle repair guides and when you enter the part you are searching, over to the right of the screen there will be a place to click on that says "vehicle repair guides", "locate the part on my vehicle" It will tell you exactly where the part is at on your make and model, and it will also tell you how to test the part, removal and replacement and also visual diagrams to help you along! I know this because i use it all the time for my car! Me being a self-reliant female makes it much easier to find and fix the problem myself! If i can, You can!!!!
