0
Crankshaft Sensors
In an internal combustion engine, a crankshaft sensor is a component used to monitor the rotational speed and position of the crankshaft. The information provided by the sensor is used by the engine control unit to manipulate ignition system timing.
2,765 Questions
What does the crank shaft sensor do exactly?
The Crankshaft position sensor, or (CKP) monitors the Crankshaft position and No#1 cylinder piston position while the engine is running. this information is sent to the engine's ECM. ( Electronic Control Module) the ECM then uses this information to calculate several operating parameters for engine performance but mostly it is used to operate the engine's Ignition system ( coil (s) and spark plugs). back in the day' you could replace your "points style distributor" for an "Electroinic-Ignition system" very much like todays MSD distributors. many of those used a Cam-sensor which essentially performed the same function. some used a Crank-sensor instead. basically:these sensors tell the ECM when to fire the spark plugs. before that it was all done with a set of "points" inside the distributor. hope this helps
Where is the cam position sensor located on a 1988 Chevy Corsica?
CLICK THE SITE AUTOZONE.COM ON THE RIGHT ---> IT SHOULD HELP YOU
Where is the crankshaft sensor on a 2003 Kia Sorento?
unfortunately the sensor is behind the plastic cover on the front of the engine and just above the crank shaft
Where is the crankshaft position sensor on a 3.0 engine in a Ford Taurus - Mercury Sable?
Most likely next to crank pulley that drives serpentine belt
For the 3.0 Vulcan 12 valve engine, it's on the front of the engine, just up to the left of the crankshaft pulley. One illustration indicates about the 11:00 o'clock position relative to the pulley, and may be obscured by waterpump.
On the 3.0 DURATEC 24 valve engine, the sensor is directly to the left of the crankshaft pulley, on the firewall SIDE of the engine. This one is easier to access through the passenger-side wheel well.
Note that the crankshaft position sensor (CKP) is only about 1 1/2" across with a small wire connector - about the only wired sensor in the general areas described above.
One last thing you may be curious about... The CKP sensors only cost about $20
1998 The crank sensor is located at the front of the engine (right side of the car) slightly to the right of the belt pulleys. It is approximately 2- 3/4 inches long and has a small cap screw on both sides that attaches it to the engine block. It has a wire lead that snaps into the top of the sensor. You can access both bolts from the top on a '98 - no sure about the '97. '96 -'99 are probably the same but would not bet on it.
if it is the 3.0L SHO motor it can be found through the passengers fender after removing the tire and the timing cover for the lower portion of the engine.
Where is the Crankshaft Position Sensor located on a 1986 Fiero?
All Fieros equipped with a distributor (1984 - 1986 4-cyl and 1985 to 1988 V6) have the crank sensor inside the distributor. It may also be known as a distributor pickup or HEI pickup.
Fieros with DIS (1987 to 1988 4 cylinder) have a crank sensor on the back side (engine side) of the ignition module extending into the engine block. The ignition module is the flat base that the ignition coils are attached to.
How do you change a crankshaft sensor on a 1994 intrepid?
Simple change out. The sensor is on passenger side of engine just behind and below the#5 sparkplug. It is held in place by a 10 M.M. bolt, and has a three wire plug that is pretty easy to unplug, provided you have 3.3L engine and I assume it is pretty much the same for larger engine also.
Where is the crankshaft sensor located on a 1996 Chevy Lumina 3.1?
On the back side of the harmonic balancer and onr bolt holds it into the timing cover
How do you replace the camshaft positioning sensor ml27 cdi?
the camshaft position sensor is on the left side of the engine , at back on the upper side .
you have to demont the conector , than unscrew and replace it
if you have changed or moved the cam it can be one tooth off and still run but the sensor will pick up the off time
How do you the replace body - engine sub-frame and bushings on a Ford Taurus - Mercury Sable?
Hire someone that has done this repair before. I have done it a few times, It's no job for the weekend wrench turner. I have paid as little as $400.00 with engine cradle included and as much as $600.00.
Sometimes, especially if you live in the rust belt, you have to cut bolts out through the floor pan, replace a couple body mounts . It can be a nightmare job. Hire a pro. Good luck.
There is an extensive thread, with tons of pictures, regarding the sub-frame bushings at the Taurus Car Club site. There are also links to Ford TSB (service bulletins) regarding the rusting problem mentioned by ClRand676 above.
See "Related Link" below
Where is the crankshaft sensor on a 2000 dodge Dakota?
On V6 and V8 models the crakshaft position sensor is mounted on the passenger side of the transmission bellhousing.
What type of problems would cause a 1995 Pontiac Bonneville to not crank?
1)bad or discharged battery -charge(12.6volts,perform draw test) or replace. 2)corroded battery terminals and posts -clean. 3)corroded battery cables -replace. 4)bad starter and/or starter relay. 5)bad ignition switch. 6)bad connection to starter. 7)melted fusible link(s). 8)broken starter signal wire. 9)alarm system has disabled starting. 10)bad transmission neutral safety switch or inhibitor switch. 11)make sure it is in "Park" 12)make sure engine isn't locked up. 13)make sure A/C compressor and other accessories are not locked up. 14)bad coded ignition key(resistor in key).
How do you replace pathfinder crank sensor?
One 10mm bolt holds the crank sensor to the top tranmission bell housing on the left side. From underneath bend the shield back that hides it and take the bolt out .. you can access the plug to disconnect the wiring easier.
How do you replace crankshaft position sensor on 1997 Chevy cavalier?
remove ac pump can just move out of the way you do not have to evacuate system remove mount that partially covers oil pan you can use an socket extension bar to tap sensor out you can see it behind crank shaft it is a real pain to get back in as it is behind engine you have to squeeze between frame and rack and pinion to get at it did you test it or are you just getting a code saying it has failed because if it is shot your care would not even turn over. There is a ignition recall that sometimes pertains to this and ignition housing anti theft resister. Just to be safe the wiring for the temp sensor and Crank position sensor can get corroded because of its location behind coolant pipes and can give you a false reading this can be repaired and wires relocated hope this helps
Does a 1988 Chevy 1500 silverado have a crank sensor?
NO it does not. If it's not firing then you need to check the ignition module, pick-up coil and the coil. Could just have a bad coil wire......
have never heard of a cam angle sensor. the cam does not change angle.it stays put in the bearings
Where is the crankshaft position sensor in a 2002 Hyundai Sonata?
It is behind the crank shaft pulley in front of the motor!
Crankshaft sensor location on a 1997 Chevy 5.7 liter engine?
if you take the skid plate off the bottom of the truck you will see the harmoic balencer. Its located on the passenger side of the truck right in the front. its a couple inches back from the belt. You should only need an 8mm socket and an extension and it should come right out.
Where is the crankshaft position sensor on a 1993 Chevy Lumina 3.1?
it is on the rear of the engine just below the middle spark plug just above the transmission oil pan
Where is the crank sensor in a 2001 Mitsubishi Montero XLS?
the crank sensor is located behind the main accessory drive pulley which is installed at the end of the crankshaft you have to remove the pulley and the plastic cover that covers the timing belt
Can someone supply a picture of the camshaft position sensor location on a 1995 subaru impreza?
its on the top of the right bank of Cylinders at the front has two wires going into it and is brown. hope this helps
Where is the camshaft sensor on a 2001 Ford F-350?
I have a 2000 F350 and mine was on the right front bottom of the engine. One bolt holds in place and easy to change. Changed it my self in 15minutes.
