0
Ford F-350
The F-350 is part of the Ford F-series. The Ford F-350 Super Duty is the 2011 version of the Ford F-350. It is available in three body designs – regular cab, crew cab and extended cab.
4,328 Questions
How do you remove air from water lines?
Install hammer arrestors at the highest point of the water lines.
What is the location of the chassis VIN on a 1973 Ford F250?
the vin number is on the door ,if not there your in trouble there is one other place its under drivers side stamped in frame .I couldn't find it on mine .so i got a form from notery and sent for it
Will a 99 v10 transmission fit a f350 7.3?
I believe it will but I do not think the torque converter will sustain the power of the 7.3L I believe the housing bolt patterns are the same.
What is the curb weight of a 1989 suburban?
Listed on the driver's door post. that is incorrect, listed on the door post is the GVW (gross vehicle weight) not the curb weight.
I've weighed my 88 4x4 twice - 5115 and 5185lbs - guess it depends on how much gas ya got.
Blown head gasket or cracked head. The gasket is blown next to the cylinder. Repair immediately. Do not drive, as severe engine damage will occur. If it is a V6 or V8, replace both head gaskets.
How can you find a diagram of the fuse box for a 1996 Hyundai Accent?
YOU MIGHT LOOK AT HMASERVICE.COM, ITS A HYUNDAI WEB SITE WITH LOTS OF TECH INFO
How many people smoke every year?
There are approximately 78,000,000 people that smoke cigarettes in the United States. The worldwide number is estimated to be more than 1 billion.
Where can you find a wiring diagram for a 1988 Acura Integra RS 5-speed?
i just saw a post...autozone.com.
How do you change injectors on 2001 f350?
First remove the valve cover and disconnect (connector) on the injector to be removed.
Second remove the rocker arms on each side of the injectors removing the two bolts holding each rocker arm also remove the push rods.
Third remember the rocker arms and push rods must be replaced in the same position as they were pirior to removel!
Fourth remove the bolt opsite the connector of the injector near the bottom of the injector head it is a 8 mm or 5/15 head bolt.
Fifth you have now losened a bracket holding the injector you should be able to push the bracket upward if so hold it there and take a small curved bar insert it under the bracket which will now move in two directions and pry up on the bracket and injector togather and guess what the injector will pop out.
Sixth now for some bad news in most cases this is like heart surgury there is going to be a great deal of oil and some fuel rush in the void you have created you will need to remove all the liquid from the injector seat and piston cavaty.
Seventh now that you have made several trips to the store for cleaning material Just reverse the process to reinstall.
One last thought it is possible to remove the injectors without removing the rocker arms though not very easy. When the rocker arms are removed the valves are closed which will help reduce the amount of oil that gets into the cylinder cavity and will save a lot of time in the longrun.
Engine model would help
NO DO NOT DO ANY OF THAT!!!! Do not remove the push rods or rocker arms?Why?? I have done hundred's if not thousands of injectors in a 7.3L and never removed them. And also an easy way to save an hydro-lock issue (which can be a real bear to push all that oil and fuel past the rings and or valves) just remove the 1/8th Allen plugs in between the 2 injectors let drain and then using a 1/4 rachet feel on the back of the head and you will feel a plug that will accept the 1/4 rachet. Just loosen and the fuel will drain out on the ground. Just wait 20-30 min to make sure and then remove ONLY the bottom bolt (the one closes to the exhaust manifold) 8mm push the hold down up and pry up. And a min amount of fuel and oil will enter the cyl. This is how the pro's do it (me). I hate shade tree wannabe knuckle buster. Anyways believe me you don't want to hydro-lock the motor. It will seem like you dropped a ball bearing in the cyl and it feels locked up hence hydro-lock. Good luck do it either way mines the right way!!!!
Powerstroke57
Where is the fuse for the washer pumps 94 ford E -350?
My manual shows 4 fuses across the bottom and the second one from the right controls the "windshield wiper/washer"
Where is the egr valve on a ford 5.8l located?
egr valve on 5.8l is located on top of engine, passenger side front bolted at intake
The term stock take simply means assessing the quality and quantity of inventory available. This is usually done in order to keep track the current number of items that were sold or still left.
What do you do if a lot of white smoke is coming out of the muffler?
Use fuel system cleaner, if it doesn't help you could have a problem with the cadalidic converter or the head gasket.
This could be because you have coolant burning inside the combustion chamber(s). If you are leaking coolant, but cannot find the leak i.e. no puddles, then it is probable that your head gasket is leaking, your head is cracked, or both. If you are handy with tools, rent/buy a compression tester. If you have low compression in two adjacent cylinders, you probably have a blown head gasket. Not an easy fix. Sorry to say that.
You may be able to get a solution from AAP that can fix the head gasket leaks. I do not know what the brand name is but they say it works. Just drain the coolant, rerun the solution through, flush and add fresh coolant. I have never tried that though.
Good luck.
Make coolant is up to level in radiator
Who makes motorcraft ignition wires?
There are various companies who are known for making motor craft ignition wires. For example, there is a company called Motorcraft.
How do you measure a wheel base on a Ford F-350 truck?
You need to know the year of the truck. The Ford website lists all specs by year and model. For example, wheelbase of the 2012 truck are as follows:
137.0" (Regular Cab)
141.8" (SWB SuperCab); 158.0" (LWB SuperCab)
156.2" (SWB Crew Cab); 172.4" (LWB Crew Cab)
