0
Honda Civic LX
The LX is a rebadged sixth-generation model of the Honda Civic. It was previously available only as a four-door car. It features 14-inch wheels, power locks and windows, front stabilizer bar, power steering, cruise control, cargo area light and a tachometer.
2,709 Questions
Does a 1993 Honda civic have a fan belt?
Technically no, the fan is driven by an electric motor. It does however have at least one drive belt (which are still refered to as fan belts) which drives the pulley for the power steering pump and the alternator.
photoelectric effect
What is the best motor oil for a 1992 Dodge Caravan Sport?
Hey Jermilla==It is really a matter of preferance but I would recommend a GOOD NAME BRAND of synthetic oil recommended by the manufacturer which is found in the owners manual. GoodluckJoe
hmmm cheapest injectors will probably be at your local parts store and as for changing them ........... step 1 remove the wiring harness from the injectors careful not to lose the clips that hold the plug to the injector then remove the 2 10mm nuts that hold the harness to the fuel rail step 2 remove the fuel lines both supply (left side ) and return (right side) from the fuel rail step 3 then remove the 3 10mm bolts from the fuel rail remove the fuel rail all injectors should come out of the intake with the fuel rail make sure all o-rings are still on the ends of the injectors if not look in the hole to make sure it is still there if not it will have to be replaced u can o-rings a the parts store also step 4 to remove the injector(s) that are bad by gently twisting and pulling the injector from the fuel rail step 5 to replace the injector all u do is push the new injector back into the hole on the fuel rail where the old injector came ( to make it a little easire u might want to put a little oil or petroleum jelly on the o-rings) step 6 reverse the instructions 1-3
Where is the block heater on a 1997 Honda civic ex?
they do not come with one stock, you would have to install an aftermarket one- Nick
Where is the ground circuit for brake lights on a Honda civic?
The ground circuit for your Honda Civic brake lights can be found on the rear frame rail. The ground circuit will be on the drivers side frame rail.
How do you get the clock and stereo to stop resetting?
For me the reason the clock and stereo were resetting was because they were losing all power from the battery. The battery was dead. maybe your cables need to be cleaned or there is a loose connection.
How do you replace the headlight bulb located on a 1998 Honda Civic HX?
Whole headlight or bulb? Bulb, just undo the retaining clip and pull out the bulb. No twist on this bulb, just straight out.
Get a light in to see the retaining clip. It has a tab to one side which you can pull and wiggle to release. It then swings away from the backside of the bulb.
OK - but undoing the wire is a bit challenging sometimes, you have to press hard on the sides of the wire clip by inserting your fingers in between the clip and the rubber seal (note the headlight will feel loose). Headlight, 4 bolts hold it in place, 2 on the top, 1 underside left and 1 underside right. DO NOT TOUCH THE BULB!!!!!!!!!!!!!!!!
What is the scheduled maintenance for a 2003 Honda Civic?
Scheduled maintenance for a 2003 Honda Civic applies to the type of service needed to keep the car running healthy. Oil changes are an example of scheduled maintenance.
What is the tightening sequence and torque for a rear head on a 2000 Chevy Malibu V6 3.1L?
IF YOUR CAR LEAKS WATER AND HEAT BLOWS COLD AIR WHAT THE PROBLEM
How do you replace ignition coil on a 2001 civic?
Pop the hood and look at the for ignition coil caps with wires running to them just above the Cat Converter on top of the front of the engine on the front of the valve cover!
1. Remove the black long plastic wire cover that says Honda on it! Need a flat head screwdriver!
2. There is a black cap nut holding each of the 4 ignition coil packs on, so you will need a 10MM socket or wrench to remove each nut!
3. Unplug the wire pack from each coil!
4. Pull upward with some pressure to remove each ignition coil. It will be snug, but not to worry as they will come out.
5. If you are also replacing the plugs, you will need a deep well socket 3/8" and a socket extension. Place the extension with socket into the well and over the spark plug and turn counter clockwise until unscrewed. To remove, pull your socket out. If the spark plug slips off the socket, I use a magnetic pickup tool to pull it out!
6. Take your new spark plug, coat threads with anti-seize being careful not to get any on the spark plug tip. place the magnetic pickup tool on top of the spark plug and carefully place the plug down into the well, and use a long screwdriver to hold the plug down and pull the magnet free! Then place your socket with extension onto the spark plug and tighten clockwise! Torque to 13 lbs!
7. Place the new ignition coil pack down into the well.
8. Before pushing it in all the way, plug in the wire pack, align the hole with the screw sticking up, and push the coil down until you feel the rubber seal snap in!
9. Place the cap screw on and hand tighten snug (doing it by feel is OK).
10. Once you have all the ignition coils installed, place the black plastic wire cover back on and you are done! With the right tools and knowledge, this job shouldn't take more than a half hour or so!
What is a transmission range switch on a 1999 Honda Civic?
It's a sensor/switch on the transmission that sends signals to the ecu( the car'a computer) to tell it what speed the car is going, and what rpm it's at, so it knows when to shift.
How many hours on average does it take to replace a timing belt on a 2000 Honda Civic?
4.4 hours of labor
What is the cost to repair or replace the head gasket and O2 sensor on a 1997 Honda Civic EX?
i had so many problems with my 95 civic.
find urself a cheap reliable mechanic. if you live in Scotland i may know a guy that could help you.
cant help u with the O2 sensor.
"Spark plugs are typically designed to have a spark gap which can be adjusted by the technician installing the spark plug, by the simple mechanism of bending the ground electrode slightly to bring it closer to or further from the center electrode. The belief that plugs are properly gapped as delivered in their box from the factory is only partially true, as proved by the fact that the same plug may be specified for several different engines, requiring a different gap for each. It can depend on the engine: new spark plugs might be pre-gapped for a V-8 engine, installing all 8 plugs unchanged; however, for a 6-cylinder engine, all (6) plugs would be re-gapped." strait from wikipedia. http://en.wikipedia.org/wiki/Spark_plug
I've had 4 Craftsman mowers. All have been right hand (standard) thread.
