0
Isuzu Rodeo
The Rodeo was a pickup truck manufactured by Isuzu from 1988 to 2002. Available as a two-door pickup truck, a two-door Spacecab pickup truck, and a four-door Crewcab pickup truck, the car features a front-engine, rear/four-wheel drive layout.
1,386 Questions
How do you change rear window lift shocks on 1998 Isuzu rodeo?
Use a small blade screwdriver to lift locking clip. Locking clip wraps around ball and goes into the socket on either end of the shock. Lift straight off. Lifting window assists in removal. Do not let go of window.
How do you fix a broken cable for the power window on the drivers side of a 96 rodeo?
Why does both reverse lights don't work on a 1998 Isuzu Rodeo?
Probably the reverse switch is bad or out of alignment. You'll need a manual to find the reverse switch. It'll be somewhere on the shifter, on the transmission, or possibly somewhere in between.
How do you install brake pads for Isuzu rodeo 2000?
How to Install Front Brake Pads
Check Related links below.
Always a good idea to buy new bolts because the old ones stretch with the heat ,and may break or will not tork down correctly .
Where is the coolant temperature sensor mounted in a 1992 Isuzu Rodeo with a v-6 engine?
you should find it on the intake manifold just behind where the upper radiator hose attaches to thermostat housing.
2001 Isuzu rodeo code p0461 mean?
Trouble code P0461 means:Fuel level sensor circuit range/performance
How do I open the hood on a 1985 Buick Skylark when the hood release cable breaks?
This can be rather tuff........you must grab the hood release cable from the underside of the vehicle. Sometimes, you can trip open the hood latch with a long screwdriver, if you know where to do it.
1. Move the driver's seat forward, and locate the security system control unit mounted on the underneath the seat.
2. Turn on ignition switch on.
3. Press and hold the green programming button on the control unit with a pen. you will have to poke through a hole about the size of a pencil located on the side of the unit. when the security system LED on the instrument panel comes on, release the program button, (Step 3 and 4 must be done within 5 seconds of each other.)
4. Press and release the top button on the transmitter, check that the LED goes out chirps once, and the front marker lights flash to confirm that the transmitter's code worked by the control unit.
5. if you have other transmitters to program, repeat steps 3 and 4.
6. Turn the ignition switch off to exit the programming mode.
I just had this problem happen to me. The alternator went bad. Replace it and it should fix the problem.
I recently experienced the same problem with my 1995 Rodeo. Fuel, Brake and Battery dashboard indicators all lit up. AC and AC Fan stopped working. Was intermittent for the first few times and then became permenant. I noticed my charge gauge reading less than 12 volts. Had alternator tested and it tested bad. Replaced the alternator and everything is back to normal again. The Rodeo has 190k miles on it btw. Other than the starter and a timing belt tensioner, this is the only part I've had to replace to date. (Water pump doesn't count because it was part of a scheduled timing belt replacement)
VCDi(Variable Geometry Turbo Charger Common Rail Diesel Injection) engine
Where is the crank sensor located on a 2004 Isuzu axiom?
Isuzu part number 8-97258-523-0(MSRP $193.86) crank sensor is on the right side(passenger) of the engine block, just behind the mount.
How do you set cam gears on Isuzu 3.5 engine?
using special tool, j-42686 pre- load the sub gear so the teeth are aligend with the cam chaft teeth then retain the sub gear sucurely with a m5 bolt inserted from the back side of the camchaft gear assmbly
How do you disarm the alarm system on a 1998 Isuzu Rodeo?
Removing the fuse doesn't work. The alarm still operates,only no,it operates when you are driving the car. the alarm will go off with no reason or warning. additionally, the door locks won't work to turn off the alarm, you must use the keychain
How do you replace coolant temp sensor on a Isuzu Rodeo?
how do you replace coolant temp sensor on a rodeo
What Manual transmission came in 1995 Isuzu Rodeo?
The manual transmission that came in 1995 Isuzu Rodeo was 21.9 US gallon engine which was ranked as 18mpg-US. This has been modified over the years with most models having automatic transmission.?æ
Where is the automatic fuel switch shut off located on a 1992 Isuzu Rodeo?
In recent experience, I have learned that a 1992 rodeo does not have a cut off switch and that on most the fuel pump is in the tank!
Where is the PVC valve on a 2001 Rodeo?
For the 3.2 L, V-6 engine, it is located on the drivers side from valve cover
How you check oil on transmission on izuzu rodeo sport 2002?
we have a 1998 rodeo and i could not find the dip stick for tranny then i went on-line and found out that these models have a sealed transmission therefore you can not check them for fluid level.
Neutral safety switch for 2001 Isuzu rodeo?
Depending on the transmission type, the neutral safety could be located in several places on the transmission. If the switch is bad, the Rodeo could either start in any gear, or not start at all.
I dont know what you mean by c-board but try this cross the green/red wire with the brown/white one.. If you have no power to the green/red wire run 12 volts to the brown/white to go up and blue/red to go down.( this is the wire color at the switch, these wires change color 2 times before making it to the motor so at the motor its blue to go down and white to go up and this is the same for both front motors and in the rear it blue/white and blue/red.
How do change the Transmission filter on a 1996 Isuzu Rodeo?
I am answering your question about a 1996 Isuzu Rodeo using my work notes from
changing the transmission filter on my 1993 Isuzu Trooper. Your 1996 may have a filler plug on the automatic transmission whereas my older Trooper has to be filled by pouring ATF down the dipstick tube.
This article tells how to do the job.
The transmission filter and 6 quarts of ATF cost $68 in 2009.
How to change a 1993 Isuzu Trooper transmission filter
Overview:
Because the Isuzu trooper is a 4 wheel drive car, there are some differences from working on a plain passenger car. The filter change job is different in these ways:
You have to remove three skid plates.
You also need to remove the rear transmission crossmember.
Watch out for rusted crossmember bolts. The frame is a closed box making broken bolt removal difficult.
You will need to lift the rear of the transmission about 1.5 inches to remove the transmission pan. The V-6 engine exhaust pipe blocks removal of the transmission pan.
The drained ATF needs to be disposed of responsibly. Determine your local procedure for disposing of used automatic transmission fluid.
Tools and supplies:
Transmission filter kit.
6 quarts Dexron III type automatic transmission fluid (ATF).
Bolt remover liquid like WD40 for crossmember and skid plate bolts.
Fastener locking liquid like Loctite medium strength blue.
Socket wrench, torque wrench and combination wrenches with these sizes:
17 mm, 14 mm, 13 mm, 10 mm
Nut driver 10 mm.
Car support blocks, transmission support block and floor jack.
Slightly longer hex bolts for lowering the transmission pan without a big spill. I use 4 pc. metric hex bolts, 6mm dia x 15 mm long from my toolbox.
Plastic bus tray (Smart and Final sells them) or 18x24" tray to catch ATF when pan is unscrewed.
Sheets of cardboard to lay on. Use to absorb ATF drips also.
Two sturdy empty plastic gallon jugs for waste ATF. Empty windshield washer jugs are suitable.
Funnel that fits the waste ATF jugs.
10 rags, 1 work shirt, 6 pairs of mechanics rubber gloves.
Work light.
Cleaning supplies:Spray bottle of degreaser like simple green, parts brushes, tub for cleaning the skid plates and crossmember, newspaper
Procedure
Jack up front of the car.
I used 6" high wheel blocks to avoid having jack stands blocking access to the transmission, also block the rear wheels and set the parking brake.
Apply WD40 or other penetrating oil and wire brush the following under car fasteners.
Rear transmission support cross member: Four bolts into frame on each side of car.
Three transmission protection skid plates. A total of about 8 bolts.
Remove three skid plates.
Use 14 mm combination wrench and ratchet wrench. The skid plates may be coated with sound deadening undercoat. Don't remove the undercoat when cleaning up the skid plates.
Put a support block to hold the rear of the transmission.
Remove the rear transmission support cross member.
Use 17 mm combination wrench and socket wrench.
If you have rusted bolts, use lots of penetrating oil to minimize the risk of breaking a bolt. From other internet posts, a broken bolt requires a removal procedure: drill, screw extractor, re-tap, new bolt.
The large crossmember bolts are 12 mm diameter x 1.25 mm pitch thread x 25 mm length.
The skid pan bolts are 10 mm diameter x 1.25 mm pitch thread x 23 mm length.
Clean the outside of the transmission pan.
I put degreaser and water in squirt bottles. I use a the degreaser with a parts brush to knock off sand, grit and oil film.
This is a good time to clean the crossmember, bolts and skid plates.
Amateur mechanics get extra brownie points for cleaning with zero oil runoff. Dry cardboard and newspaper absorbs ATF and degreaser spray.
Unscrew transmission pan bolts.
Here is a gradual scheme that helps avoid bending the pan and spilling ATF:
Go all the way around the pan and loosen all bolts 1 turn,
Remove 4 corner bolts completely and put in 4 longer bolts from your toolbox. This allows you to lower the pan and remove the other bolts without the pan dropping.
Using fingers, remove the corner bolts and gradually tip the pan and spill the ATF into the bus tray.
Raise the rear of the transmission about 1 1/2" so the transmission pan can be removed.
There are different ways of doing this. I used the floor jack, leaving the support blocks ready to hold the transmission when the pan was removed.
Open the new transmission filter package with clean hands and verify your replacement parts are the right shape.
Remove the old transmission filter, it has 3 bolts with 13 mm socket size.
Clean the transmission pan. Remember to put the round chip magnet back in the pan (I forgot!)
Clean the transmission gasket mating surface.
Reassemble. See your shop manual for torque specifications. Here are torque specifications I used:
Filter bolts ( 13 mm socket size) torque 15 ft-lb.
Transmission pan bolts ( 10 mm socket size ) 96 inch-lb.
Crossmember bolts, due to the absence of lock washers I used Loctite on all crossmember bolts. I couldn't get a torque specification so I pulled the bolts to a solid engagement at about 65 ft-lb.
Refill the transmission.
You can estimate the quarts of ATF needed to refill the transmission by carefully looking at the quantity of used ATF you collected in the clean empty sturdy gallon jugs you were so lucky to use as I mentioned above. My 1993 Isuzu drain volume was 5 or 5 1/2 quarts of drained fluid.
The filler on the 1993 Isuzu is the dipstick tube.
Use a small funnel to assist pouring fluid into the dipstick tube.
Get the exact fluid fill level using the instructions in the owners manual.
How do you adjust clutch on 92 rodeo?
There is not any adjustment on this clutch. Al you have to do is bleed the system.
