answersLogoWhite

0


Best Answer

Recent experience leads me to believe it can be done. I think one can use an (ohm) meter to find the resistance of the chip in the ignition key, and just jump the connection with the correct resistance. Get the resistors needed from Radio Shack and build a circuit that equals the needed ohms, and connect it to the wires instead of the orange 2-wire cable that comes from the VATS key tumbler. Your SECURITY light may come on and stay on, but at least the car will run. I have a 1996 Grand Prix I purchased used in 2006. A couple months ago I came out of a store to find my car wouldn't start, and a SECURITY light blinking while the key is on. The problem turned out to be a broken wire on the tumbler set. My mechanic installed a new tumbler set, I got a new key made at a GM dealer, and all was well. Thankfully I kept the old tumbler with it's broken wire, because tonight the car started blinking SECURITY and not starting again, and the old tumbler came in handy. (I suspect the wire broke on the new tumbler too, because the design is not durable...two small fragile-looking wires that move every time the key is turned are the weak link in the design.) Anyway, I had to plug the old tumbler back in, hold the broken wire together with one hand, and try to start the car with the other. Luckily, this worked. I now have a side-effect though. After the car was running, I didn't continue to hold the broken wires together, and the SECURITY light came on and stayed on throughout the 15 mile drive to my mechanic's garage. I expected to be unable to start the car again after turning it off, at least not without trying the wire trick again, but to my surprise the car now starts without the VATS key connection from the tumbler set plugged in at all! Trouble is, now I'm unsure whether and when I will have a problem again. My security system is not stopping the car from running even though I don't have the wires plugged in anymore. This is a good thing, until it decides to revert to it's normal function, which I'm afraid it will do at the worst possible time.

User Avatar

Wiki User

13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: 1996 Pontiac Grand Prix security system bypass?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do i disable the anti theft system on my 1996 Pontiac grand?

I need to know how to bypass the anti theft system pass key on a 1997 Pontiac grand am. my car will start but goes dead. wont remain running


To reset security sistem 2001 Pontiac grand am?

how i can reset the security sistem for a Pontiac 2001 grand am


Does the 2003 Gran Prix have a security system?

The 2003 Pontiac Grand Prix does come with a factory security system installed. If your security system is enabled it should have a "security" light that flashes when the key is turned on.


Can the factory security system on a 1999 Pontiac Grand Am GT be disabled and if so how?

Pull the fuse.


How do you disengage the security system on a 2001 Pontiac grand am?

have same trouble i would like to know myself


How can you disable the factory security system on a 1999 Pontiac Grand Am GT?

No, it is hardwired into the ecm and the rest of the car.


If the security system has a problem on your Pontiac Grand Am does it shut the gas pump off?

Yes. When your GM security system activates, it disables fuel delivery to prevent startup.


How do you fix power windows on Pontiac grand am they won't go up?

1999 Pontiac grand pre how do I bypass driver window so I can get it up.


How do you find a Tension pullley assembly bypass tube on 98 Pontiac grand prix gt?

Look for it.


2003 Pontiac grand am turns over and wont start?

security lock out had same problem with our 2004 grand am


Can you bypass the supercharger on a 1993 Pontiac grand prix?

Grand Prix's in '93 did not come with superchargers. Supercharged engines were not introduced until the 1997 model year.


Where is the coolant temp sensor on a 1993 Pontiac Grand Am 3.3L?

its underneathe the alternater, right next to the bypass hose inlet.