In a half wave rectifier voltage across load resistance is not consistent, because for positive pulse of input voltage diode work as a forward bias i,e half wave rectifier treat as closed circuit and for negative pulse of a input voltage diode work as a reverse bias so no current flow through circuit. therefore voltage output is not consistent. In full wave rectifier two diodes are used at the both side of secondary coil of transformer. due to that for positive pulse of input voltage one diode diode work as a forward bias another as a reverse bias. for negative pulse of a input voltage second diode work as a forward bias another as a reverse bias,so consistent voltage can be provided by full wave rectifier.the nature of output voltage of half wave rectifier and full wave rectifier is that it flows through with only one polarity either in positive or negative in the circuit.
There are more than two conditions that can make a thyristor conduct, but the general (functional) ones are: 1) positive voltage form anode to cathode, and 2) a positive voltage on the trigger input (referenced to the cathode) for a standard polarity thyristor. Other conditions can be: A) Anode-Cathode Voltage exceeding thyristor witholding voltage. B) Overtemperature of the thyristor chip C) Faulty thyristor (can be caused by overloads)
A positive DC voltage is an electric potential where excess electrons will flow from negative to positive.AnswerYou appear to be mixing up potential difference (i.e. voltage) with potential. There is no such thing as a 'positive' voltage if you mean 'positive' in the sense of charge! 'Voltage' means 'potential difference', and you cannot have a positive or negative potential difference in this sense. You can only apply positive and negative in this sense to potentials.However, if you mean 'positive' in the sense of direction, then a positive voltage is one that is acting in the opposite direction to a negative voltage within the same circuit. For example, where two batteries have been connected in opposition.
It will be 7805 in which 7 is company code; 8 means positive voltage & 05 is amount of positive voltage output.
VAC is voltage of alternating current signalDC current is amperage of a direct current signalAnswerYour question contradicts itself, as the symbol, V,represents voltage, not current.However, V a.c., represents an alternating voltage -one in which the direction in which the voltage is acting continuously reverses itself. Vd.c. represents a direct voltage, in which the voltage continuously acts in the same direction.
No, a pulse of positive voltage typically represents a binary 1 in digital electronics. A binary 0 is usually represented by a low voltage or ground signal.
1
A pulse is just a pulse. Its meaning depends on context and the design of the system.
A pulse is just a pulse. Its meaning depends on context and the design of the system.
One A2:In positive logic (most logics), a High, that is, a positive voltage over about 3.5 volts, is considered a "one".
pulse of positive voltage is not indicate to zero
Positive, zero, zero, positive
Good? You need to be more specific - computer (API) changes what you see on the screen to - readable computer language, machine or binary. Which has two choices on or off or 0 or 1 or positive vs negative (or plain English is the light off or on). Her is a better question: A digital signal composed of a pulse of positive voltage represents an 1 or a positive.
In a half wave rectifier voltage across load resistance is not consistent, because for positive pulse of input voltage diode work as a forward bias i,e half wave rectifier treat as closed circuit and for negative pulse of a input voltage diode work as a reverse bias so no current flow through circuit. therefore voltage output is not consistent. In full wave rectifier two diodes are used at the both side of secondary coil of transformer. due to that for positive pulse of input voltage one diode diode work as a forward bias another as a reverse bias. for negative pulse of a input voltage second diode work as a forward bias another as a reverse bias,so consistent voltage can be provided by full wave rectifier.the nature of output voltage of half wave rectifier and full wave rectifier is that it flows through with only one polarity either in positive or negative in the circuit.
The power of a battery is typically measured in voltage (V) and current (A). The voltage represents the electrical potential difference between the positive and negative terminals, while the current represents the rate of flow of electricity. The power output of a battery is the product of voltage and current (P = V x I).
a generator of single or multiple voltage pulses; usually adjustable for pulse rate
It equals a negative.. (: