0
No. A 277 volt ballast needs the correct voltage to operate. The 277 voltage is derived from the star point voltage of a 480 volt three phase system (277/480). The 208 voltage is a three phase line voltage whose star-point voltage is 120 volts (120/208).
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you convert 380v 3 phase to 220v 3 phase?
Mathematically, just divide 480 by the square root of three. Electrically, 480V refers to the line-to-line value of a three phase system. For example, measure the voltage across A-phase and B-phase and you'll get 480V. 277V is the line-to-neutral value. Measure the voltage across A-phase and the neutral conductor and you should get 277V.
How do you come up with 277 volts?
The star point or wye voltage of a 480 volt three phase four wire system is 277 volts. The 480 voltage is divided by the sq root of 3 (for 3 phases). The sq root of 3 is 1.73. 480 volts/1.73 = 277 volts. The same formula is used on all three phase four wire systems. 208 volts /1.73 = 120 volts, 416 volts /1.73 = 240 volts, 600 volts / 1.73 = 347 volts.
What voltage can be deadly?
Electrical current is a fascinating and powerful tool. It can be both safe and deadly: the emissions from a Tesla coil, while awe inspiring, pass harmlessly around and through humans; yet, ramp up the current enough, and severe effects can occur.The major factors that affect a person are: the amount of current, measured in amperes or "amps"; the path the current takes through the body (i.e. through the heart); and the length of time the body is exposed as a circuit.The voltage, environmental moisture, whether the heart is in a beat or not, and the person's health can also affect the severity of the shock. The following list details effects of current. Note that 1000 milliamperes (mA) equates to 1 ampere (A).1 mA of current causes a bit of a tingling sensation, but can be dangerous under some conditions.5mA of current results in a slight painless shock. Strong involuntary reactions can cause injuries to the person.6-16mA results in a painful shock, and the individual is less likely to have control over their muscles.17-99mA results in extreme pain, respiratory arrest and strong muscular contractions. Death is quite probable at this point.100mA-2A results in uneven, uncoordinated pumping of the heart. Nerve damage begins here. Death is highly likely.At more than 2 amperes, the heart stops, internal organs begin to cook, and sever burns occur. Death is quite probable without immediate medical assistance.See the related links below for further details.
Wiring diagram for 277 v ballast?
wireing diadram for 277v ballast
What is the difference in amps used by lighting wired 277v vs 208v?
Answer for USA, Canada and countries running a 60 Hz supply service.Assuming you are using the same fixture, and assuming the fixture can operate on either voltage, you will get fewer amps with 208v than with 277v. However, a fixture designed for 208v will probably burn up on 277v, and a fixture designed for 277v will probably not produce any light on 208v.The two fixtures in reality are quite different. The 277v fixture is using one leg and neutral of a 277/480v 3 phase 4 wire system and the 208v fixture is using 2 legs of a 120/208v 3 phase 4 wire system.In commercial and industrial installations the 277v fixture is most common.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
What is low voltage transmission?
In the supply industry it refers to circuits of below 1000 volts. Common voltages used are 120v, 208v, 230v, 240v, 277v, 400v, 415v, 480v.
What's wrong with a 240V outlet that tests at 277V?
What's the reading at the service panel? What do regular 115V outlets read at? What kind of meter are you using? Chances are you have 480/277V 3 phase power to this building. Whoever wired the outlet used a 277V feed, possibly because 240V was not avaliable. You should call an electrician, repair of this problem may involve instalation of a transformer.
How do you get a 120 - 480 Volt ballast to work from a normal outlet?
Most often this ballast is actually 120/277. It could be 120-480 though. Look at the diagram on the ballast itself. Many times there will either be a black/white/green, black/red/white/green, or black/orange/white/green set of primary leads. If the ballast has only black/white/green, but it shows more than one voltage, chances are it is automatically adjusted for the line voltage. In this case, just connect the black/white/green to a typical lighting box, and the ballast will light your lamps. If the ballast has more than one color other than white or green, it is a multi-tapped ballast. Normally the black lead is for 120v line voltage and the red or orange is 277v. Don't assume though, refer to the diagram sticker located on the ballast for this information. Hook up the 120v, neutral, and ground to your lighting box, but be sure to cap the unused 277v lead with a wire nut. ----If you do not understand the work well enough to accomplish it yourself properly and safely, don't try it. Consult a professional electrician, as they are proficient enough to do it properly and safely. When working on electrical circuits and equipment, make sure to de-energize the circuit you will be working on. Then test the circuit with a definitive means to make sure it is off (multimeter with metal tipped leads, voltage tester with metal tipped leads, etc., not a non-contact tester, which is non-definitive.)
Will 120 - 277 volt electronic fluorescent ballasts work on 208 volts?
NO! a 120-277 electronic ballast requires one "hot" wire and a neutral from either a 110V or 277V supply. If you supply it with two "hot" wires from a 208 V supply, it will instantly burn up.Yes. A ballast with a specification range of 120 volt to 277 volt will work on 208 volt. These ballast use intelligent voltage sensing technology and it does not matter if the source is a hot and neutral or two (2) hots. Don't believe it? Call a ballast manufacturer instead of giving incorrect answers.
Can you lower 277v to 240v?
With a transformer.
Why use 277v light fixtures instead of 110v light fixtures?
277v light fixtures are more efficient to operate and less expensive to install than a 110v fixture of identical wattage. 277v light fixtures are typically installed when 480V 3 Phase primary electric service supplies a commercial or industrial facility. 277v lighting circuits are single phase circuits using one of the 480v primary phases (A,B & C) to Neutral. The higher voltage allows more fixtures per circuit using smaller conductors and longer runs typically required in warehouse lighting applications. ( Amps = Watts/Volts: 400W/277V Fixture = 1.4 Amps, 400W/110V fixture = 3.6 Amps) With 480V 3 Phase primary service, 110V Single Phase power is created using a Step-down transformer. The voltage transformation process consumes power (kWh) and the 277V fixture will consume less kWh than a 110V fixture if identical wattage, especially in fixtures with ballasts such as fluorescent or High Intensity Discharge (HID), like Sodium, Metal Halide or Mercury Vapor.
Where does 277v power used in America?
It is used in Industrial lighting.
What should be the primisable voltage between neutral and earth in a three phase system?
It is the line to line voltage divided by 1.73. 600V / 1.73 = 347V 480V / 1.73 = 277V 380V / 1.73 = 220V 208V / 1.73 = 120V
Does a 277 volt fluorescent fixture cost less to operate than a 120 volt fixture?
Not necessarily. It's the wattage of the lamps that determine how much power is used. 277V lighting merely allows for more lights to be on a circuit than if they were on a 120V. The current that is printed on the ballast, times the voltage the ballast is connected to, is what determines the cost to operate the fixture. This is the true wattage of the fixture. The wattage of the lamps are independent as new electronic ballasts can power a numerous amount of tubes of various wattages.
Will 277V work with a 120V ballast?
The impedence of the ballast is system voltage dependent to allow required current to pass through the light fixture. If system voltage changes, the current passing through the light fixture changes, therefore to get designed output from the fixture, the ballast has to be changed.
