0
What else can I help you with?
Changeing switch on a craftman tablesaw with a household switch?
Run the Hot black and the Natural White so that both sides are cut when the switch is off.
Can I use a 30 amp circuit with a 12 gauge wire to handle a tablesaw that runs at 13 amps under load but spikes above 30 amps on turning on as the 20 amp circuit kept tripping at turn on?
This is proper connection for a motor that has a full load amperage of 13 amps. The wire size for motors has to be 125% of the full load amperage from the nameplate on the motor. On a 13 amp motor this relates to 16.25 amps. The next wire size up from this current is #12 rated at 20 amps. If you are using a fractional motor starter switch to control this motor, the heater size for the switch should have a rating of 16.25 amps. The fusing for wire is 40 amps for non time delay fuses, 25 amps for time delay fuses or a 30 amp circuit breaker.
What is a device used to open and close an electric circuit?
The device is called a switch.
How do you rewire an outlet to work independently and not by a light switch?
Most switched outlets have one half that's hot all the time. If that's the case it will be as easy as changeing the outlet. In the center of each side of the outlet there is a small piece of copper connecting the two screws. Look and see if the copper piece is broken on the hot side, if it is then replace the outlet using the constant hot. Cap off the unused wire from the switch. If both sides of the outlet are switched then you can remove the two wires from the switch and tie them together. then either replace the switch and have a dummy or put on a blank cover. You should be all set.
Where does the neutral wire go on a single pole switch?
Unless the switch has a light to indicate the switch is turned on, there is no neutral connection to a single pole switch.
Changeing switch on a craftman tablesaw with a household switch?
Run the Hot black and the Natural White so that both sides are cut when the switch is off.
Where is the ignition switch on a 1997 Hyundai Accent and how do you change it?
changeing ignition barral
Can you play two families at once on the sims 3?
no but you can switch households. you can do this by clicking edit town then clicking the household you want to switch to then clicking change to active household.
What is the purpose of an outlet with a switch and how does it function in a household setting?
An outlet with a switch allows you to control the flow of electricity to a device or appliance plugged into it. The switch can turn the power on or off, providing convenience and energy savings in a household setting.
What amp light switch used in common household?
That would be a single pole 15 amp switch
What causes lowered voltage in a household switch?
A; Assuming the source is good there can be extreme loads or a bad contact o the switch
What fues controls the signal lights and radio and heater of a Jeep Cherokee Sport?
I don't know which fuse those are but. I don know most of the time I have all of those out at the same time my igntion switch has over heated and needs to be replaced. After many many times of changeing the switch I put a relay in there that runs the power and konw that wire on the switch is the signal. Haven't had that problem since.
How can I properly install and troubleshoot household switch wiring?
To properly install and troubleshoot household switch wiring, follow these steps: Turn off the power to the circuit at the breaker box. Remove the old switch and disconnect the wires. Connect the new switch by matching the wires to the corresponding terminals. Secure the switch in place and turn the power back on. Test the switch to ensure it is working properly. If the switch is not working, check for loose connections or faulty wiring. Remember to always follow safety precautions when working with electricity. If you are unsure, consult a professional electrician.
What is the basic light switch wiring diagram for a standard household electrical setup?
The basic light switch wiring diagram for a standard household electrical setup involves connecting the hot wire from the power source to one terminal of the switch, and then connecting the hot wire from the light fixture to the other terminal of the switch. The neutral wires from both the power source and the light fixture are connected together. This setup allows the switch to control the flow of electricity to the light fixture.
How does a 3 way outlet switch function in a household electrical system?
A 3-way outlet switch in a household electrical system allows you to control a single light or appliance from two different locations. This is achieved by using two separate switches that are connected to the same light or appliance. When one switch is turned on, the circuit is completed and the light or appliance turns on. When the other switch is turned on, the circuit is completed in a different way, turning the light or appliance off.
What is the purpose of a fuse switch box and how does it function in a household electrical system?
The purpose of a fuse switch box is to protect the electrical system in a household from overloading and short circuits. It functions by containing fuses that break the circuit when too much current flows through, preventing damage to the system and reducing the risk of fire.
What is the function of a well water pressure switch in a water system and how does it impact the water pressure in a household?
The function of a well water pressure switch in a water system is to regulate the water pressure by turning the pump on and off as needed. It impacts the water pressure in a household by maintaining a consistent pressure level, ensuring a steady flow of water for various household activities like showering, washing dishes, and doing laundry.
