What is the head bolt tightening sequence and torque for a 1992 Chevy Corsica 22 ltr 4-cylinder?
Check www.60degreev6.com -Kyle email@example.com
Asked in Auto Parts and Repairs, Head Gaskets and Valve Covers, Nissan Pathfinder, Honda Motorcycles
Head bolt torque and removal sequence for 1994 Nissan pathfinder?
The 1994 Nissan Pathfinder had bolt torque specification is 140 pounds. There is not any removal sequence. There is only a sequence to put the bolts in. ...
Cylinder head tightening sequence 1990 Toyota Cressida?
Pls let me know the cylinder head bolt tightening sequence for toyota cressida mx83 ...
Asked in Chevy Lumina, Chevy Malibu, Grand Prix SE
What are the head bolt torque specs for a 1995 Pontiac 3.1 liter head bolts?
What is the head bolt torque for a 1997 chevy lumina four cylinder?
Asked in Toyota, Toyota Corolla
What is the head bolt sequence and torque settings for a ae86 Toyota carolla?
Refer to the factory manual for correct sequence. Loosening sequence if different to tightening, and both should be done in steps, not all at once. Lightly oil thread and under head of bolts and torque as instructed in the manual. Use a new head gasket and clean the head and block surfaces. Take care not to scratch or damage the sealing surfaces. Use a torque wrench and the proper 10mm 12 point deep socket. ...
Asked in Cars & Vehicles, Fiat Punto
What is fiat punto head bolt tightening sequence and torque?
It is important to know the head bolt tightening sequence and the torque of a vehicle. For the Fiat Punto it is 20nm, 30nm, 90 degree turn, 90 degree turn, then in order 8,6,2,5,10,7,3,1,4,9. ...
Asked in Chevy 350
How do you find the cylinder head bolt torque sequence for a 1989 Chevy 350?
You need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library. ...
Asked in Chevy Lumina
Cylinder head torque specifications for a 1997 Chevy 3100?
33 ft. lbs. plus an additional 1/4 turn on the bolt. Don't forget that there is also a torque sequence as well. ...
Asked in Chevrolet
What is the head bolt tightening sequence for a 6 cylinder 235 Chevy engine?
Forgive the text illustration, but the sequence is like this: 13 14 9 10 5 6 1 2 4 3 8 7 12 11 "1" is on the passenger's side, middle bolt of the seven head bolts on each side. Torque in sequence to 40 lbs on the first pass. Then to 70 ft-lbs in sequence. Final torque is 90-100 all across the board. ...
Asked in Fuel and Engines, Pontiac Sunbird
What is torque sequence for heads on 1993 Pontiac sunbird?
A 1993 Pontiac Sunbird head bolt torque sequence recommends starting at one and of the head and alternating to the other end of the head. You should end up in the middle. ...
What is the proper big block Chevy head bolt torque sequence?
Here is a site that provides the sequence: http://www.autozone.com/az/cds/en_us/0900823d/80/11/bc/70/0900823d8011bc70/repairInfoPages.htm#hd1-1-1 Just arrow down and it will show you the sequence for 6 cyl, SBC and BBC. ...
Cylinder head tightening sequence for Vauxhall Vectra?
The cylinder had bolt tightening sequence should begin by tightening the head bolts on each end of the head. Tighten the center head bolts. Work towards each end of the head, alternating back and forth. ...
Asked in Chevy 350
What if coolant squirts out from head bolt hole once head bolt was removed on a 350 is that normal or is the block cracked?
That is NORMAL. The head bolts go stright into the water jackets on all Chevy engines. ...
What are the head bolt torque specs for a 1997 Chevy 5.7?
65 ft lbs - reached in 3 equal steps - just about any auto parts store should be able to print out the pattern sequence for you application, ...